Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
UCS C シリーズサーバ：Bug Trend 2024年7-9月
by daiogawa -
Secure Access で Experience Insights を利用する際のクライアント NPCAP バージョンについて
by Ryuji Nozaka -
eXR: NCS系列のQoSの"Policer committed rate"と"Policer conform burst"について
by kaztaked -
Secure Access で行う "高度なアプリケーション制御" が正常動作しない場合の対処方法
by Ryuji Nozaka -
Best Practices in Migrating from NID to Official Containerized NSO
by Pannag Desai -
how to see the line vty session time-out in NX-OS
by Sudqi -
IPSec VPN "Up-Active" but No Traffic Passing Between Cisco and Bintec
by Thomas27100 -
Unable to configure 802.1x on Cisco 9200
by richard.jackson
Community Activity
C9124AXE model outdoor device indoor environment display on controller
in advanced deployment mode. here I see the device as indoor. it also says that I can change it from the default AP profile. but the default AP profile covers all antennas. I can't predict how my indoor devices will be affected when I make this chang...
Resolved! AP2800 - Mobility Express conversion no space on device
Hi all,I've picked up a few AP2802 access points. My plan is to convert one to ME software and have the rest as regular CAPWAP access points subordinate to it.I can't get the conversion process to work though. I've done a MODE button 20s factory rese...
monitor-session is not working in ios-xr ? Help needed
Hi all, I am trying to capture the packets from Cisco NCS-IOS XR but everytime i try to open the file it shows this error "the capture file has no Interface Description Blocks" My configurations are mentioned below. does someone has any idea that wh...
Unable to configure 802.1x on Cisco 9200
Hi, I'm working with a client to deploy 802.1x on Cisco 9200 access switches. All but one switch are working successfully. However, one device is not accepting the command "authentication order dot1x mab" and returns the message that the command is d...
Consultation on Roaming Optimization for WIFI6
Hello everyone.I am currently using WLC5520-8.10.196 and AP9115AXI in the office. I have noticed that some clients occasionally roam to farther APs. These clients are all Intel's WIFI6 network cards. The frequency band of AP is 80MHz.The AP3800 serie...
Resolved! Anyconnect connection for ISP1 fails, ISP2 works
Hi, I have configured two ISPs (WAN1, WAN2). VPN with anyconnect was already working for both ISPs. Today when doing final tests, VPN for ISP1 on WAN1 is not working anymore. ISP2 on WAN2 still works. ASA log shows: 1 Starting SSL handshake with clie...
SD-WAN Single Router Dual WAN - Active/Standby Transport Configs
Hello Community, I recently deployed active/standby set up for single router dual circuit where one circuit has slower speed and was meant to be a backup line incase primary failed. I made following two config changes to make it work and was curious...
Resolved! Add multiple Network devices in same group in Cisco ISE
Hi. First post ever so I might be doing this wrong....I am to add a new /24 network in an existing Network Device list.This due to the existing IP range is for a temporary setup still running in a temporary location and I am now setting up the perman...
Moving access points and clients from 5508 to 9800 WLC
So we have old 5508 controllers in our environment which has access points and clients on them. We also have 9800 WLC in our environment on the same switches. We are planning to move the access points and clients between the two controllers and wante...
ISE v3.2 patch 5 - API Network Device Group Creation
Hi all We try to add network device groups to all Location with python headers = {'content-type' : 'application/json', 'Accept':'application/jsson'} payload="{"NetworkDeviceGroup" : {"name" : "Location#All Locations#AA","ngdtype" : "Location","desc...
Connection error
I would appreciate any help! I am working on "Getting Started with Cisco Packet Tracer. Deploying devices in the packet Tracer but keeps getting this error message.
Cisco Catalyst Management Center
Hi, Customer want to buy around 28 Cisco Catalyst Switches with Cisco DNA Essentials license. My question is: If we want to install Cisco Catalyst management Center and add all of those 28 switches into Management center and use virtual appliance do ...
What is SFTP used for?
What is SFTP used for in Cisco, and in general networking? How often, what for? thanks
CME with FXO caller-id show unknown number (inbound)
Hi All,Currently setup CME with FXO connected to telco, call is able in and outbound, but when calling in caller-id showing unknow number on phone.Router version 15.4please find attach for configuration and log when inbound call.
C9407R IOS-XE upgrade question
I was looking through the downloads section and noticed that IOS-XE 17.12.4 is now suggested for install on the 9407R Supervisor Engine-1.I also noticed that in the software on chassis section it only suggests 17.9.5. Anyone know why this is or what ...
