The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi, I'm having problems to redirect incoming call from sip trunk to CUE AA,- I have a Cisco 3945 and a NME-CUE , VID: V04- the sip trunk provider only gives the last four digits.- sip trunk number 8800 redirects to extension 100. Works fine.- sip t...
Hello,It's possible to identify QoS traffic based on DSCP values. For example, for the EF class, by using the command "match ip dscp ef". But, how is the correct DSCP value set for specific traffic?I know that with some applications, the user can hav...
anyone to help with my switch, logging the following logs and rebooting automatically.before it reboots the syst and rps lights light amber and then the fan off the reboots!#model: CS-2960x-48FPS-L
Hello team,I need to upgrade both the standby and active WLCs using the CLI. However, I couldn't find the method to upgrade the standby WLC via CLI in the official Cisco documentation. Could you please share the procedure? I believe the standby WLC h...
Here and there, i see posts on the interwebs that invite crusaders for IPV6, and I don't think the position typically held during said conversations holds a mature enough perspective. I'm hoping i can get some views here with Cisco engineers and see ...
I was having issues in setting up a C1111-8PWA-WS for the first time and decided to start from scratch. Unfortunately I used the factory-reset all command instead of using a paper clip in the button on the back of the unit and now I am in rommon mod...
Can we upgrade the WLC 9800 from IOS version 17.06.04 to IOS version Cupertino 17.9.3 directly ? Current IOS version : 17.06.04 Upgraded IOS version: 17.09.03 WLC Model: C9800-L-C-K9. Can we upgrade directly from 17.06.4 to 17.09.03 ? And new IOS ver...
Hi Everyone,I’ve set up a lab in GNS3 using the EIGRP protocol, as shown in the attached diagram.Everything was working fine until I created a VRF interface on R2.Now, I’m facing some connectivity issues:-Loopback 1 can ping and reach Loopback 2 but ...
Hi all,I'm trying to setup ISE to perform a simple MAB profiling for a printer. For some reason ISE rejects the printer the first time I connect it:Event5400 Authentication failedFailure Reason15039 Rejected per authorization profile I am using an au...
Hi, I created an attached lab in GNS3 and recently added a VMware VM Microsoft Server 2019 into the topology. I am having an issue where I can ping all the network devices and all the VLAN's in the topology from the server to all devices, however, I...
I converted my C9105AXI to EWC and now I want to switch it back to CAPWAP. I tried following the directions from the post below.https://community.cisco.com/t5/wireless/how-to-convert-from-ewc-to-capwap-mode/td-p/4663375wireless ewc-ap ap shell usern...
FMC started throwing Health Alert: URL Filtering registration token expires in XX days, where XX is reducing day by day. Classic licensing. ASA with Firepower module, 6.6.7.1. Could disable health monitoring for this feature, but would like to under...
Sometimes you want to see how the tunnel and the transport modes works with encapsulation, especially when using GRE over IPSEC and you would like to decrypt the ESP or IPSEC packet to see how GRE packet is encapulated with the two modes, especially ...
Hello,I have a distributed ISE deployment as below:ISE 3.1 patch 6PSN: 3 physical & 3 VM Admin: 1physical & 1VMMnT: 1physical & 1VM aaa group server radius ISERadiusserver name ISE-VMserver name ISE-physicalip radius source-interface xxaaa server rad...