Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1988036members
1344101discussions

Community Activity

Pinging of VLANS (Core and Access Switch)

Have you ever experienced VLAN issues? I'm facing an issue where my laptop should be able to ping all VLANs, but it can only ping the VLAN it's assigned to.Here's what I encountered:1. I enabled IP routing on the C9500, but when I run the "show run" ...

Advice to replace ANY in acl

Hi, I need some advice. I have an ACL1 with four internal VLANs as source (VLAN1, VLAN2, VLAN3, VLAN4). All of them have permitted access via tcp/80 and tcp/443 to destination ANY (WAN). ACL2 permits VLAN3 to access a host in VLAN10 via tcp/21. The p...

mcgiga by Level 1
  • 87 Views
  • 2 replies
  • 0 Helpful votes

SFP Model to Part Number conversion sheet

Hello,I am looking for a list that will show both Model names to Part number on any Cisco SFPs.Examples:Model name “SFP-10G-SR-S” = Part Number 10-3105-01Model name “SFP-10G-SR” = Part Number 10-2415-03Model name “SFP-GE-T EXT” = Part Number 30-1421-...

Kraig by Level 1
  • 104 Views
  • 4 replies
  • 0 Helpful votes

Enable BGP HA Graceful Restart

hi,i'm running IPSec VPN betwen HQ and a branch.i need to add the BGP HA graceful restart in the branch dual internet edge router.there's an iBGP between the branch's dual internet edge router and fortigate HA FW (which runs IPSec).my question, is it...

johnlloyd_13_0-1728028701402.png

ISR Vlan Interface IP Address assigned by DHCP (Client)

I am using a Cisco C1111 ISR w/ 2 L3 interfaces, 8 L2 interfaces. Interface Vlan601 currently has an IP address assigned to it. I would like to use DHCP to assign the IP address to this interface. However, when I change it to DHCP, the MAC address in...

judu by Level 1
  • 904 Views
  • 31 replies
  • 0 Helpful votes

Call Transfer in CUCM

Hi,Cisco CUCM (11.5.1.12900-21)I would like to know if there is specific kind of transfer available to use, specificly, when call goes into first phone and wants to transfer that call to second phone with a click of a button, is this feature availabl...

saba53 by Level 1
  • 123 Views
  • 4 replies
  • 0 Helpful votes

Auto attendant CUE SIP Trunking

Hi, I'm having problems to redirect incoming call from sip trunk to  CUE AA,- I have a Cisco 3945 and  a NME-CUE , VID: V04- the sip trunk provider only gives the last four digits.- sip trunk number 8800 redirects to extension 100. Works fine.- sip t...

kotushaMx by Level 1
  • 177 Views
  • 8 replies
  • 0 Helpful votes

C1111-8PWA-WS mistakenly factory reset

I was having issues in setting up a C1111-8PWA-WS for the first time and decided to start from scratch.  Unfortunately I used the factory-reset all command instead of using a paper clip in the button on the back of the unit and now I am in rommon mod...

prevent email spoofing

Hi All, Need to enable Validity Check on the Sender's Domain i.e Envelope sender dns verification and Verify the From Header Using DMARC i.e applying an Enforce or Quarantine dmarc profile to Mail flow policy.  Basically i need to know what will be t...

Vishal6_0-1728104946741.png Vishal6_1-1728104987480.png
Vishal6 by Level 1
  • 51 Views
  • 0 replies
  • 0 Helpful votes

Hardare Certification by Country

I need to verify if a given Cisco-made product or component is certified for a given country.  Different countries have different regulatory standards, and the hardest thing to find is whether or not a given component is green-lit by a given governme...

trmoon-19 by Level 1
  • 29 Views
  • 0 replies
  • 0 Helpful votes