Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1990248members
1347148discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Connecting comcast internet to home lab

HiI have comcast internet that is coming from a Arris Mode SB6180, the comcast IP address is 73.56.x.x. I need to be able to set up the WAN to my Cisco 2811 router, the mode is not set as DHCP, I connect  the cable coming the ARRIS modem to f0/0 port...

Gregaku by • Level 1
  • 42 Views
  • 0 replies
  • 0 Helpful votes

bridge-domain interface in Cisco IOS-XR

Hello Everyone,Hope all of you are doing fine. Recently I'm trying to make router routed interface into bridge interface so that I can send packet from PC1 to PC2 via same broadcasting bridge domain. I used iox-xr router for the LAB. My configuration...

siblirayhan_0-1728718179401.png

Layer 3 Cannot Ping next hop

Hello all,  I need help here. I just set up two routers and two layer 3 switches. Can someone check my settings? I cannot ping over to 3.3.3.1 or vice versa. I attached the PKT file. Please rename it back to PKT from PNG.   I greatly greatly apprecia...

RV160 Openvpn nightmare

I've been trying to set up OpenVPN on a new RV160 but the GUI is getting stuck once I click apply and stays on the screen: Please wait for a moment (as you can see in the screenshot)So far I have tried the following: Changed browsersChanged computers...

wcutajar by • Level 1
  • 747 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Hospital 9800-40 HA upgrade to 17.9.3

Hi all, I need to upgrade a pair of 9800-40s in HA from 17.6.4 to 17.9.3 at a local hospital. While I have done an staging upgrade on the 9800-40s before production, I need a flawless upgrade plan for the hospital to minimize or eliminate downtime. A...

lcaruso by • Level 6
  • 1391 Views
  • 11 replies
  • 0 Helpful votes

Cisco ASA 5520 Config help.

ciscoasa# show int Interface GigabitEthernet0/0 "outside", is up, line protocol is up Hardware is i82546GB rev03, BW 1000 Mbps, DLY 10 usec Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps) MAC address 001b.2ac2.5068, MTU 1500 IP address ...

Cisco c9200 with c8200 network chaos

Hello,Apologies for the not very specific subject title. Im working on a production system, which many mistakes have been made today with compounding hardware issues on top of it. Im very stress rn, will have to go back tomorrow to make sure my rever...

hayden by • Level 1
  • 166 Views
  • 4 replies
  • 0 Helpful votes

cp-6941 french locale

Hello ,I'm looking for to download the french locale for the CP-6941 phone.I'm using freepbx and need the user locale and the network locale .I checked cisco's download site and found only the firmware ...Tyvm for your insights

Arkheon59 by • Level 1
  • 73 Views
  • 0 replies
  • 0 Helpful votes

ASAv sur EVE-NG

Bonjour à tous, je ne sais pas si quelq'un peut m'aider à cernet ce probleme:apres toutes les configurations, le pc du Lan1 peut ( ping) l'interface 1 du router2 mais pas le pc du Lan2 et le PC du Lan2 arrive à faire un ping vers l;interface 1 du rou...

Screenshot.png

Cios AP 2802I-E autonomous

bonjour,Mon entreprise changeant ses AP wifi pour les dernières générations j'ai eu l'occasion de récupérer une AP modèle cité en sujet, seulement j'ai besoin du firmware pour la passer en autonomous. Je ne connais personne avec un compte cisco me pe...

Atalec by • Spotlight
  • 63 Views
  • 0 replies
  • 0 Helpful votes

dúvida ITN-CCNA-200-301

o que seria o Exame final de habilidades do ITN (equipamento)?terminei todos os módulos, mas esse ainda está aberto e não me deixa encerrar. já fiz os testes teóricos e práticos.tem um botão ligar e uma área para carregar um anexo.na trilha de conteú...

Load more