AIR-AP1852E-K9 Stacting on boot

Hi,I have one 1852E in mobility express mode and I having problem with him.When I want to configure him and I connecting to him using console cable (Putty with configuration: 8,1, none,none) he stacking on boot Reseting him using mode button not work...

Unable to access Cisco 4221 web login page

Hi,We have a cisco 4221 router. When I try accessing its GUI page on https://192.168.10.1 its not letting me access that.What all I have tried and not working is as follows:Tried older version of firefox which supports TLS 1Tried fiddling with the fi...

CCNAv7 Lab 7.3.7 S2 not response to ping

I've encountered issue as the Cisco Switch 2960 (configured as S2) in the lab does not response to ping.PC-A can ping PC-B and S1PC-B can ping PC-A and S1S1 can ping PC-A and PC-BS2 failed to ping S1, PC-A and PC-BS1, PC-A, PC-B failed to ping S2It l...

Sdwan

we can make combination between cisco 8200 and 8200L as edge Router in the same sdwan solution

Cisco FTD failover - Interface Virtual MAC Queries

Hello, I am working on setting up HA for FTD appliances for a customer. I have been using the syntax aaaa.bbbb.xxx1 and aaaa.bbbb.xxx2 usually for assigning interface virtual MACs on the primary and secondary respectively. I have the below queries re...

Created DMZ

Hello everyone, please help me. I want to create 3 sections: INSIDE, OUTSIDE and DMZ. With OUTSIDE it is possible to ping, and access services in the DMZ. INSIDE also does the same thing and it has the addition of being able to ping OUTSIDE(8.8.8.8),...

Curso Fundamentos do Phyton

Monitoring Traffic Consumption by MAC Address

Dear Team,I am currently using the Wi-Fi Mobility Express model AIR-AP1815I-I-K9, with WPA2 Personal authentication and MAC filtering enabled.Is there any way to track the traffic consumption for each MAC address on a daily or weekly basis?Thanks in ...

ISE intermittent authentication drops

Running Cisco ISE v3 with 6 PSNs no load balancer across a campus network.On 3 individual occasions over the last few weeks clients have stopped authenticating and we have seen the health score drop.  The workaround has been to restart the ISE servic...

Open connect VPN is asking for password even though I put password

Hi,I tried to join open connect for my Sandbox lab access it is asking for password again and again.. I put user name and password using the email received from cisco. It seems my account needs to be fixed as authentication is failing. 

IP Phone Ringing but no voice

HelloI am experiencing some strange issue with my VOIP in 1 of my branches.  our branches are connected thru IP VPN and 1 of our branches are able to call our office in HQ (ringing but no voice) other branches are able to call our office without any ...

Connecting comcast internet to home lab

HiI have comcast internet that is coming from a Arris Mode SB6180, the comcast IP address is 73.56.x.x. I need to be able to set up the WAN to my Cisco 2811 router, the mode is not set as DHCP, I connect  the cable coming the ARRIS modem to f0/0 port...

FTD CLI - Display the FTD active/standby unit in the hostname

Hello, I would like to know if there is any enhancement done to display the FTD active/standby unit in the hostname of the respective FTD CLI. In the ASA we have the command "prompt hostname priority state cisco ftd". Can we do anything similar in FT...

Cisco FTD CLI - Management IP shown as 203.0.113.130

Hello, When I login to the FTD CLI, and check the management IP is shown as 203.0.113.130. My FTD version is 7.4.2. I checked in another FTD in version 7.2, but it is showing as "Unassigned". Please advise. Thanks Shabeeb          

SG300-28P identifies itself as a duplicate IGMP Querier IP address

25-Jun-2015 08:44:45 %BRG_IGMP_QRR-W-DUPLICATE_IP: Duplicate IGMP Querier IP address 192.168.142.1 detected on VLAN 1. Remote MAC address is 34:a8:4e:0d:34:55. I am seeing this regularly on this SG300-28P switch.  These IP and MAC addresses belongs t...