Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Welcome back to the CSM Partner Community!
by Rbritolo -
Quick-Boiling Mini Kettle: Dev Desk Essential?
by bigelectronicstore09 -
4G LTE Config on IR1101 - Commands not working
by Akash-Hegde -
CSCwo09244 - IOSlice temperature sensor shows as failed
by offshorestoragesupport -
Catalyst EVPN multihoming for non-fabric networks
by loger9901 -
Need assistance in fixing the uccx script
by ziakhan86 -
CCP Express 3.5 の「Application Visibility and Control」を初期設定後に有効にする手順
by maniwa-net -
Can I ISSU upgrade a C9410R from 17.9.6 to 17.12.6 directly
by scottsassin
Community Activity
Quick-Boiling Mini Kettle: Dev Desk Essential?
Hey Cisco DevNet crew! Long coding marathons and late-night lab sessions demand quick caffeine fixes, but bulky kettles just clutter desks and slow you down. This mini electric tea kettle solves that with fast boils and portability tailored for devs ...
No Health Check poll from the Primary Health Check Node
Hi All,We have ISE deployment in distributed deployment architecture with two PSN nodes and two PAN nodes. In the PAN failover setting the primary health check node is set to PSN01, and the secondary is set to PSN02. We are currently seeing alarms st...
CBD network topology not right
Current SituationWe are encountering an issue with the network topology. The setup consists of 10 switches, all running firmware C1200-24P-4G and using the same model (C1200-24P-4G). These switches are organized into two clusters:Cluster 1: 7 switche...
Resolved! Cisco ISE OVA 37xx or 38xx
Hi, Our customer wants a 50k Shared PSN (Cisco ISE node has multiple personas), so the OVA that we will use is the Cisco-vISE-600-3.4.0.608b.ova but which deployment can we use? The 600-Medium 37xx or 600-Medium 38xx? For the 3.4 version is better to...
C1300X Fans
Are the fans on the C1300X switches thermally controlled?
Resolved! Download c1140-k9w7-tar.153-3.JB.tar ?
Hello all ! I'm searching where i can download this software "c1140-k9w7-tar.153-3.JB.tar" for my access-point. Can you give me a link where i can download it please ? Thank's
4G LTE Config on IR1101 - Commands not working
Hi I am using Telstra SIM card on Cisco IR1101, with slot 0/1/0. The current problem is all the profiles inactive, non public IP shown during show run. I called Telstra and they told the SIM is active and tested the internet connecting to phone Same ...
Cisco Packet Tracer Network Scanning
Not sure if this is the right place for this questions but... I work at a place that using the Cisco Packet Tracer software and have been for years until today. We have been banned from updating to the new PT version of 9.0.0 because our security/ ne...
CSCwo09244 - IOSlice temperature sensor shows as failed
The logs are uploaded and let us know the status.
Catalyst EVPN multihoming for non-fabric networks
Are there any configuration guides available for this feature for Catalyst 9300/9300x? We would like to configure and test for an upcoming design.
CCNA EXAM LAB QUESTIONS
Hi, I'll be sitting my CCNA exam in Feb of this year. Regarding the lab questions in the exam, do i have to type out the full command when in the CLI? eg: Could i just type "en" instead of "enable" or "conf t" instead of "configure terminal" ?? Any...
BPDU Guard
Just a simple question why it's recommended to use both Portfast and BPDU Guard together apart from the very fact that both should be used in access switches ports connecting to end users?? Like BPDU Guard will still work if I don't have portfast con...
Routing to SVI Over Trunk in IOS XE - Can reach hosts but not GW?
Good morning Cisco Community, I feel like i am over looking something simple here. I've built a SVI and propogated it into OSPF on a L3 device. On one interface of that device there is a host connected through two cascaded layer two acces switches....
Need assistance in fixing the uccx script
We have one script that was downloaded from the old UCCX 8.6 system and then uploaded to the new UCCX 15 system. When using this script, I am unable to answer calls from the Finesse desktop, although I can answer the calls from the phone. The other s...
Cisco 2802i AUX Port as LAN Port
Following the instruction from the link below, I converted the AUX port of one of our Cisco 2802i AP's to a LAN port. My hope was to feed a switch from it so I could provide network access to three devices. So far, I can not gain network access. Has ...
