SOME LINES REMOVED FOR CLARITY Cisco Configuration Assistant. Version: 3.2 (3). Sat Mar 28 12:08:45 PDT 2015Using keyboard-interactive authentication. Password: Aden_UC540#service-module integrated-Service-Engine 0/0 status Service Module is Cisco Integrated-Service-Engine0/0 Service Module supports session via TTY line 2 Service Module is in Steady state Service Module heartbeat-reset is enabled Getting status from the Service Module, please wait.. Cisco Unity Express 7.1.3 CUE is on UC500UC500 Aden_UC540#show int integrated-Service-Engine 0/0 Integrated-Service-Engine0/0 is up, line protocol is up Hardware is PQII_PRO_UEC, address is 68ef.bdb5.47a1 (bia 68ef.bdb5.47a1) Description: cue is initialized with default IMAP group Interface is unnumbered. Using address of Loopback0 (10.1.10.2) MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:03, output 00:00:03, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 10672 packets input, 642200 bytes, 0 no buffer Received 4 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 5386 packets output, 1999778 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Aden_UC540#service Aden_UC540#service-module inte Aden_UC540#service-module integrated-Service-Engine 0/0 session Trying 10.1.10.2, 2002 ... Open Cisco Configuration Assistant. Version: 3.2 (3). Sat Mar 28 12:08:45 PDT 2015 User Access Verification Username: cisco Password: Please answer y or n. #FIXME Need hook to display app specific message IMPORTANT:: IMPORTANT:: **************************************************************** IMPORTANT:: The system has detected that the database is corrupted. IMPORTANT:: This could have been caused by a power failure, an unclean IMPORTANT:: shutdown (a reset done from IOS) or a failed restore. IMPORTANT:: IMPORTANT:: You have 2 options: IMPORTANT:: IMPORTANT:: 1) Clean the database, this means you will loose application data. IMPORTANT:: IMPORTANT:: The system can be recovered completely (including the above IMPORTANT:: information) by doing a restore of configuration and data. IMPORTANT:: IMPORTANT:: 2) Bypass cleaning the database and let the system try to IMPORTANT:: recover the database. If this fails the system will reboot IMPORTANT:: and you will be reprompted with this menu and you should IMPORTANT:: then choose option 1 to clean the database. IMPORTANT:: IMPORTANT:: **************************************************************** IMPORTANT:: Do you want to clean the database (y,n)?n The system will attempt to repair the database. It is possible, though, that the system will not work properly. Serial Number: read workflow properties finish setting sysdb callagent INIT: Entering runlevel: 2 ********** rc.post_install **************** INIT: Switching to runlevel: 4 INIT: Sending processes the TERM signal STARTED: ntp_startup.sh STARTED: LDAP_startup.sh STARTED: SQL_startup.sh STARTED: dwnldr_startup.sh STARTED: HTTP_startup.sh STARTED: probe STARTED: superthread_startup.sh STARTED: ${ROOT}/usr/bin/products/herbie/herbie_startup.sh STARTED: ${ROOT}/usr/wfavvid/run Waiting 590 ... malloc: subst.c:2628: assertion botched malloc: block on free list clobbered Stopping myself... Waiting 3 ...MONITOR EXITING... SAVE TRACE BUFFER Dec 3 14:14:46 localhost err_handler: CRASH appsServices startup startup.sh System has crashed. The trace buffer information is stored in the file "atrace_save.log". You can upload the file using "copy log" command INIT: Switching to runlevel: 6 INIT: Sending processes the TERM signal Rebooting ... shutdown: sending all processes the TERM signal... sql: INFO sql server output END shutdown: sending all processes the KILL signal. shutdown: turning off swap shutdown: unmounting all file systems Please stand by Restarting system. Cisco BootMon Version: 1.0.3 (Jul 27 2007 - 10:41:10) MPC83XX Bootmon starts Bootmon: cold reset. System now booting. Bootmon: reading primary bootloader image Bootmon: calling bootloader Cisco ServiceEngine Bootloader Version: 1.0.3 (Jul 6 2007 - 10:15:37) MPC83XX Resetting devices ....Done. mac address for internal ethernet 68:ef:bd:b5:47:be Please enter '***' to change boot configuration: ServicesEngine Bootloader Version : 1.0.3 kern_sz: 1128869 bl_boot_cf_cmd root=/dev/hda1 install_root=ide ro plat=freddo ## Booting image at 04000000 ... Image Name: Linux-2.6.22-cisco-freddo Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1128805 Bytes = 1.1 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.6.22.10-vs2.2.0.5-cisco-freddo (drodrig@fndn-bld-system8) (gcc version 4.2.2) #1 Sat Nov 21 16:44:32 PST 2009 Zone PFN ranges: DMA 0 -> 131072 Normal 131072 -> 131072 early_node_map[1] active PFN ranges 0: 0 -> 131072 Built 1 zonelists. Total pages: 130048 Kernel command line: root=/dev/hda1 install_root=ide ro plat=freddo Platform: ise IPIC (128 IRQ sources, 8 External IRQs) at fe000700 PID hash table entries: 2048 (order: 11, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 515840k available (1756k kernel code, 516k data, 92k init, 0k highmem) in atrace_init log_head: h: 0, t: 403531, l: 0, w: 0, s: 1047488 Using existing trace log log_head: h: 0, t: 403531, l: 0, w: 0, s: 1047488 Mount-cache hash table entries: 512 NET: Registered protocol family 16 Generic PHY: Registered new driver SCSI subsystem initialized NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Cisco ContentEngine Flash Driver Version 0.03 ceflash: Can't register misc device Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize Gianfar MII Bus: probed eth0: Gianfar Ethernet Controller Version 1.2, 68:ef:bd:b5:47:be eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth1: Gianfar Ethernet Controller Version 1.2, 68:ef:bd:b5:47:bf eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx hda: probing with STATUS(0x50) instead of ALTSTATUS(0x0a) hda: UNIGEN FLASH, ATA DISK drive ide0 at 0xe1000000-0xe1000007,0xe100280d on irq 17 hda: max request size: 128KiB hda: 4096512 sectors (2097 MB) w/1KiB Cache, CHS=4064/16/63 hda: set_multmode: status=0x51 { DriveReady SeekComplete Error } hda: set_multmode: error=0x04 { DriveStatusError } ide: failed opcode was: 0xef hda: cache flushes supported hda: hda1 hda2 i2c /dev entries driver NET: Registered protocol family 26 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ReiserFS: hda1: found reiserfs format "3.6" with standard journal ReiserFS: hda1: using ordered data mode ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda1: checking transaction log (hda1) ReiserFS: hda1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 92k init Cisco init INIT: version 2.86 booting mounting proc fs ... mounting sys fs ... mounting /dev/shm tmpfs ... reiser root fs ... ****************************************************** * Warning: The dma on your hard drive is turned off. * * This may really slow down the fsck process. * ****************************************************** Reiserfs super block in block 16 on 0x0 of format 3.6 with standard journal Blocks (total/free): 510544/423519 by 4096 bytes Filesystem is clean Filesystem seems mounted read-only. Skipping journal replay. Checking internal tree..finished FILESYSTEM CLEAN Remounting the root filesystem read-write... kernel.sem = 1900 4000 32 100 vm.overcommit_memory = 1 Welcome to Cisco Service Engine Setting the system time from system log Thu Dec 3 14:15:00 PST 2015 ********** rc.aesop **************** Populating resource values from /etc/freddo_rsrc_file Populating resource values from /etc/default_rsrc_file Populating resource values from /etc/products/cue/default_rsrc_file Populating resource values from /etc/products/cue/freddo_rsrc_file Populating resource values from /usr/etc/products/herbie/freddo_rsrc_file Populating resource values from /usr/etc/products/isis/freddo_rsrc_file Populating resource values from /usr/etc/products/madrox/freddo_rsrc_file Populating resource values from /usr/etc/products/timecardview/default_rsrc_file Populating resource values from /usr/etc/products/timecardview/freddo_rsrc_file Processing manifests . . . . . . . . . . . . . . . . . complete Bad pte = 1fd91304, process = sysdb, vm_flags = 75, vaddr = fe1509b ==> Management interface is eth0 ==> Management interface is eth0 Serial Number: read workflow properties finish setting sysdb callagent INIT: Entering runlevel: 2 ********** rc.post_install **************** INIT: Switching to runlevel: 4 INIT: Sending processes the TERM signal STARTED: ntp_startup.sh STARTED: LDAP_startup.sh STARTED: SQL_startup.sh STARTED: dwnldr_startup.sh STARTED: HTTP_startup.sh STARTED: probe STARTED: superthread_startup.sh STARTED: ${ROOT}/usr/bin/products/herbie/herbie_startup.sh STARTED: ${ROOT}/usr/wfavvid/run Waiting 5 ...MONITOR EXITING... SAVE TRACE BUFFER Dec 3 14:16:13 localhost err_handler: CRASH appsServices startup startup.sh System has crashed. The trace buffer information is stored in the file "atrace_save.log". You can upload the file using "copy log" command INIT: Sending processes the TERM signal Rebooting ... shutdown: sending all processes the TERM signal... platform.config: INFO platform.config server output END trace: INFO trace daemon output END shutdown: sending all processes the KILL signal. shutdown: turning off swap shutdown: unmounting all file systems Please stand by Restarting system. Cisco BootMon Version: 1.0.3 (Jul 27 2007 - 10:41:10) MPC83XX Bootmon starts Bootmon: cold reset. System now booting. Bootmon: reading primary bootloader image Bootmon: calling bootloader Cisco ServiceEngine Bootloader Version: 1.0.3 (Jul 6 2007 - 10:15:37) MPC83XX Resetting devices ....Done. mac address for internal ethernet 68:ef:bd:b5:47:be Please enter '***' to change boot configuration: ServicesEngine Bootloader Version : 1.0.3 kern_sz: 1128869 bl_boot_cf_cmd root=/dev/hda1 install_root=ide ro plat=freddo ## Booting image at 04000000 ... Image Name: Linux-2.6.22-cisco-freddo Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1128805 Bytes = 1.1 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.6.22.10-vs2.2.0.5-cisco-freddo (drodrig@fndn-bld-system8) (gcc version 4.2.2) #1 Sat Nov 21 16:44:32 PST 2009 Zone PFN ranges: DMA 0 -> 131072 Normal 131072 -> 131072 early_node_map[1] active PFN ranges 0: 0 -> 131072 Built 1 zonelists. Total pages: 130048 Kernel command line: root=/dev/hda1 install_root=ide ro plat=freddo Platform: ise IPIC (128 IRQ sources, 8 External IRQs) at fe000700 PID hash table entries: 2048 (order: 11, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 515840k available (1756k kernel code, 516k data, 92k init, 0k highmem) in atrace_init log_head: h: 0, t: 404622, l: 0, w: 0, s: 1047488 Using existing trace log log_head: h: 0, t: 404622, l: 0, w: 0, s: 1047488 Mount-cache hash table entries: 512 NET: Registered protocol family 16 Generic PHY: Registered new driver SCSI subsystem initialized NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Cisco ContentEngine Flash Driver Version 0.03 ceflash: Can't register misc device Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize Gianfar MII Bus: probed eth0: Gianfar Ethernet Controller Version 1.2, 68:ef:bd:b5:47:be eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth1: Gianfar Ethernet Controller Version 1.2, 68:ef:bd:b5:47:bf eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx hda: probing with STATUS(0x50) instead of ALTSTATUS(0x0a) hda: UNIGEN FLASH, ATA DISK drive ide0 at 0xe1000000-0xe1000007,0xe100280d on irq 17 hda: max request size: 128KiB hda: 4096512 sectors (2097 MB) w/1KiB Cache, CHS=4064/16/63 hda: set_multmode: status=0x51 { DriveReady SeekComplete Error } hda: set_multmode: error=0x04 { DriveStatusError } ide: failed opcode was: 0xef hda: cache flushes supported hda: hda1 hda2 i2c /dev entries driver NET: Registered protocol family 26 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ReiserFS: hda1: found reiserfs format "3.6" with standard journal ReiserFS: hda1: using ordered data mode ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda1: checking transaction log (hda1) ReiserFS: hda1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 92k init Cisco init INIT: version 2.86 booting mounting proc fs ... mounting sys fs ... mounting /dev/shm tmpfs ... reiser root fs ... ****************************************************** * Warning: The dma on your hard drive is turned off. * * This may really slow down the fsck process. * ****************************************************** Reiserfs super block in block 16 on 0x0 of format 3.6 with standard journal Blocks (total/free): 510544/423660 by 4096 bytes Filesystem is clean Filesystem seems mounted read-only. Skipping journal replay. Checking internal tree..finished FILESYSTEM CLEAN Remounting the root filesystem read-write... kernel.sem = 1900 4000 32 100 vm.overcommit_memory = 1 Welcome to Cisco Service Engine Setting the system time from system log Thu Dec 3 14:19:00 PST 2015 ********** rc.aesop **************** Populating resource values from /etc/freddo_rsrc_file Populating resource values from /etc/default_rsrc_file Populating resource values from /etc/products/cue/default_rsrc_file Populating resource values from /etc/products/cue/freddo_rsrc_file Populating resource values from /usr/etc/products/herbie/freddo_rsrc_file Populating resource values from /usr/etc/products/isis/freddo_rsrc_file Populating resource values from /usr/etc/products/madrox/freddo_rsrc_file Populating resource values from /usr/etc/products/timecardview/default_rsrc_file Populating resource values from /usr/etc/products/timecardview/freddo_rsrc_file Processing manifests . . . . . . . . . . . . . . . . . complete Bad pte = 1fd91304, process = sysdb, vm_flags = 75, vaddr = fe1509b Bad pte = 1fd91304, process = sysdb, vm_flags = 75, vaddr = fe1509b Bad pte = 1fd91304, process = sysdb, vm_flags = 75, vaddr = fe1509b ==> Management interface is eth0 ==> Management interface is eth0 Serial Number: read workflow properties finish setting sysdb callagent INIT: Entering runlevel: 2 ********** rc.post_install **************** INIT: Switching to runlevel: 4 INIT: Sending processes the TERM signal STARTED: ntp_startup.sh STARTED: LDAP_startup.sh STARTED: SQL_startup.sh STARTED: dwnldr_startup.sh STARTED: HTTP_startup.sh STARTED: probe STARTED: superthread_startup.sh STARTED: ${ROOT}/usr/bin/products/herbie/herbie_startup.sh STARTED: ${ROOT}/usr/wfavvid/run Waiting 5 ...Bad pte = 1c627784, process = java, vm_flags = 100077, vaddr = 31a0f04c Waiting 12 ...Oops: kernel access of bad area, sig: 11 [#1] NIP: c00311e4 LR: c00311bc CTR: c003151c REGS: d9f71d70 TRAP: 0300 Not tainted (2.6.22.10-vs2.2.0.5-cisco-freddo) MSR: 00009032 CR: 24002448 XER: 00000000 DAR: 00000001, DSISR: 20000000 TASK = da240870[2219] 'sleep' THREAD: d9f70000 GPR00: fffffff9 d9f71e20 da240870 ddf6f124 00000000 d9f71e28 00000000 0fd0db48 GPR08: c45afe81 7fef1000 4a8c3576 522cd413 44000448 100be0a8 c01dc5b8 c01ddb98 GPR16: c01dc634 c01dc61c c023c9a8 c01dc65c 100bf228 00000000 0000f932 0fd0db48 GPR24: 00000000 00000000 ffffffda 00000001 00000000 00000000 c024667c fffffff5 NIP [c00311e4] futex_wake+0x80/0x114 LR [c00311bc] futex_wake+0x58/0x114 Call Trace: [d9f71e20] [c00311ac] futex_wake+0x48/0x114 (unreliable) [d9f71e50] [c003152c] do_futex+0x2b4/0xbb4 [d9f71ef0] [c0031f04] sys_futex+0xd8/0x194 [d9f71f40] [c0003dfc] ret_from_syscall+0x0/0x38 Instruction dump: 7fc3f378 4bffe8b9 81230008 7c7e1b78 3809fff8 7f801800 3869fff4 8123000c 419e0070 3be9fff4 4800001c 381f0004 <813f000c> 7f80f000 7fe3fb78 3be9fff4 Oops: kernel access of bad area, sig: 11 [#2] NIP: c0031ac0 LR: c003166c CTR: c0031ce8 REGS: da25bda0 TRAP: 0300 Not tainted (2.6.22.10-vs2.2.0.5-cisco-freddo) MSR: 00009032 CR: 27422688 XER: 00000000 DAR: 00000001, DSISR: 20000000 TASK = db651110[2214] 'java' THREAD: da25a000 GPR00: fffffff9 da25be50 db651110 ddf6f124 00000000 da25be64 00000000 100801a8 GPR08: 7607ec28 10080000 00000001 ddf6f144 477b4682 1002705c da25be64 da25be58 GPR16: 00000000 00000001 00000000 00000004 00000000 00000004 da25a000 00000001 GPR24: 00000000 00000001 00000000 00000001 100801ac c024628c c024667c fffffff5 NIP [c0031ac0] do_futex+0x848/0xbb4 LR [c003166c] do_futex+0x3f4/0xbb4 Call Trace: [da25be50] [c003164c] do_futex+0x3d4/0xbb4 (unreliable) [da25bef0] [c0031f04] sys_futex+0xd8/0x194 [da25bf40] [c0003dfc] ret_from_syscall+0x0/0x38 Instruction dump: 2e000000 419201a0 41900334 813e0008 3809fff8 7f80f000 3869fff4 8123000c 419e0068 3be9fff4 4800001c 381f0004 <813f000c> 7f80f000 419e0050 7fe3fb78 /bin/cli_startup.sh: line 63: 2219 Segmentation fault sleep 1 Waiting 14 ...MONITOR EXITING... SAVE TRACE BUFFER Dec 3 14:20:22 localhost err_handler: CRASH appsServices startup startup.sh System has crashed. The trace buffer information is stored in the file "atrace_save.log". You can upload the file using "copy log" command Waiting 17 ...Oops: kernel access of bad area, sig: 11 [#3] NIP: c00311e4 LR: c00311bc CTR: c003151c REGS: dde03d70 TRAP: 0300 Not tainted (2.6.22.10-vs2.2.0.5-cisco-freddo) MSR: 00009032 CR: 24002448 XER: 00000000 DAR: 00000001, DSISR: 20000000 TASK = ddd7c470[2250] 'sysdb' THREAD: dde02000 GPR00: fffffff9 dde03e20 ddd7c470 ddf6f124 00000000 dde03e28 00000000 0ff7bb48 GPR08: cf36fba3 7f902000 43563129 4b8323b5 44000448 100be0a8 00000022 100b93e4 GPR16: 00000000 7f812758 00000000 1008ff74 100ca2c8 00000000 0000f932 0ff7bb48 GPR24: 00000000 00000000 ffffffda 00000001 00000000 00000000 c024667c fffffff5 NIP [c00311e4] futex_wake+0x80/0x114 LR [c00311bc] futex_wake+0x58/0x114 Call Trace: [dde03e20] [c00311ac] futex_wake+0x48/0x114 (unreliable) [dde03e50] [c003152c] do_futex+0x2b4/0xbb4 [dde03ef0] [c0031f04] sys_futex+0xd8/0x194 [dde03f40] [c0003dfc] ret_from_syscall+0x0/0x38 Instruction dump: 7fc3f378 4bffe8b9 81230008 7c7e1b78 3809fff8 7f801800 3869fff4 8123000c 419e0070 3be9fff4 4800001c 381f0004 <813f000c> 7f80f000 7fe3fb78 3be9fff4 INIT: Sending processes the TERM signal Rebooting ... shutdown: sending all processes the TERM signal... trace: INFO trace daemon output END platform.config: INFO platform.config server output END shutdown: sending all processes the KILL signal. shutdown: turning off swap shutdown: unmounting all file systems Please stand by Restarting system. Cisco BootMon Version: 1.0.3 (Jul 27 2007 - 10:41:10) MPC83XX Bootmon starts Bootmon: cold reset. System now booting. Bootmon: reading primary bootloader image Bootmon: calling bootloader Cisco ServiceEngine Bootloader Version: 1.0.3 (Jul 6 2007 - 10:15:37) MPC83XX Resetting devices ....Done. mac address for internal ethernet 68:ef:bd:b5:47:be Please enter '***' to change boot configuration: *** ServicesEngine Bootloader Version : 1.0.3 ServicesEngine boot-loader> ? ? - alias for 'help' boot - boot from specified src config - configure various params help - print online help ping - send ICMP ECHO_REQUEST to network host reboot - Perform RESET of the CPU show - show config, trace or version verify - verify software versions ServicesEngine boot-loader> show ? Usage: show show config - display config show trace - display trace buffer show version - display boot-loader version ServicesEngine boot-loader> show config IP Address: 0.0.0.0 Subnet Mask: 255.255.255.0 TFTP Server: 10.1.1.1 Gateway: 10.1.1.60 Default Helper-file: cue-installer.ise.7.0.3 Ethernet Interface: internal Default Boot: disk Default Bootloader: primary Bootloader Version: 1.0.3 ServicesEngine boot-loader> ? ? - alias for 'help' boot - boot from specified src config - configure various params help - print online help ping - send ICMP ECHO_REQUEST to network host reboot - Perform RESET of the CPU show - show config, trace or version verify - verify software versions ServicesEngine boot-loader> verify ? Usage: verify verify - no argument required ServicesEngine boot-loader> verify kern_sz: 1128869 verify root=/dev/hda1 ro plat=freddo 7 ## Booting image at 04000000 ... Image Name: Linux-2.6.22-cisco-freddo Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1128805 Bytes = 1.1 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.6.22.10-vs2.2.0.5-cisco-freddo (drodrig@fndn-bld-system8) (gcc version 4.2.2) #1 Sat Nov 21 16:44:32 PST 2009 Zone PFN ranges: DMA 0 -> 131072 Normal 131072 -> 131072 early_node_map[1] active PFN ranges 0: 0 -> 131072 Built 1 zonelists. Total pages: 130048 Kernel command line: root=/dev/hda1 ro plat=freddo 7 Platform: ise IPIC (128 IRQ sources, 8 External IRQs) at fe000700 PID hash table entries: 2048 (order: 11, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 515840k available (1756k kernel code, 516k data, 92k init, 0k highmem) in atrace_init log_head: h: 0, t: 404706, l: 0, w: 0, s: 1047488 Using existing trace log log_head: h: 0, t: 404706, l: 0, w: 0, s: 1047488 Mount-cache hash table entries: 512 NET: Registered protocol family 16 Generic PHY: Registered new driver SCSI subsystem initialized NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Cisco ContentEngine Flash Driver Version 0.03 ceflash: Can't register misc device Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize Gianfar MII Bus: probed eth0: Gianfar Ethernet Controller Version 1.2, 68:ef:bd:b5:47:be eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth1: Gianfar Ethernet Controller Version 1.2, 68:ef:bd:b5:47:bf eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx hda: probing with STATUS(0x50) instead of ALTSTATUS(0x0a) hda: UNIGEN FLASH, ATA DISK drive ide0 at 0xe1000000-0xe1000007,0xe100280d on irq 17 hda: max request size: 128KiB hda: 4096512 sectors (2097 MB) w/1KiB Cache, CHS=4064/16/63 hda: set_multmode: status=0x51 { DriveReady SeekComplete Error } hda: set_multmode: error=0x04 { DriveStatusError } ide: failed opcode was: 0xef hda: cache flushes supported hda: hda1 hda2 i2c /dev entries driver NET: Registered protocol family 26 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ReiserFS: hda1: found reiserfs format "3.6" with standard journal ReiserFS: hda1: using ordered data mode ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda1: checking transaction log (hda1) ReiserFS: hda1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 92k init Cisco init INIT: version 2.86 booting mounting proc fs ... mounting sys fs ... mounting /dev/shm tmpfs ... reiser root fs ... ****************************************************** * Warning: The dma on your hard drive is turned off. * * This may really slow down the fsck process. * ****************************************************** Reiserfs super block in block 16 on 0x0 of format 3.6 with standard journal Blocks (total/free): 510544/423658 by 4096 bytes Filesystem is clean Filesystem seems mounted read-only. Skipping journal replay. Checking internal tree..finished FILESYSTEM CLEAN Remounting the root filesystem read-write... kernel.sem = 1900 4000 32 100 vm.overcommit_memory = 1 Welcome to Cisco Service Engine Setting the system time from system log Thu Dec 3 14:20:00 PST 2015 ********** rc.aesop **************** Populating resource values from /etc/freddo_rsrc_file Populating resource values from /etc/default_rsrc_file Populating resource values from /etc/products/cue/default_rsrc_file Populating resource values from /etc/products/cue/freddo_rsrc_file Populating resource values from /usr/etc/products/herbie/freddo_rsrc_file Populating resource values from /usr/etc/products/isis/freddo_rsrc_file Populating resource values from /usr/etc/products/madrox/freddo_rsrc_file Populating resource values from /usr/etc/products/timecardview/default_rsrc_file malloc: variables.c:1688: assertion botched free: called with unallocated block argument Stopping myself.../etc/rc.d/rc.aesop: line 42: 137 Aborted /bin/rsrcmgr.sh Processing manifests . . . . . . . . . . . . . . . . . complete Bad pte = 1fd91304, process = sysdb, vm_flags = 75, vaddr = fe1509b Bad pte = 1fd91304, process = sysdb, vm_flags = 75, vaddr = fe1509b Bad pte = 1fd91304, process = sysdb, vm_flags = 75, vaddr = fe1509b Bad pte = 1fd91304, process = sysdb, vm_flags = 75, vaddr = fe1509b ==> Management interface is eth0 ==> Management interface is eth0 Skipping router communication server initialization Skipping IOS Registration... verify requested. Serial Number: read workflow properties finish setting sysdb callagent INIT: Entering runlevel: 7 ********** rc.verify **************** Hardware: - Module type: Integrated-Service-Engine - Memory (Bytes): 515984 CPU0: - CPU: e300c1 - Core Clock (MHz): 500 Installed Packages: - Installer 7.1.3.0 - PhoneConnect 7.0.0 - ServiceManager 7.1.3 - Thirdparty 7.1.3 - Bootloader (Primary) 1.0.3 - Infrastructure 2.3.2.2 - CUE Voicemail Language Support 7.1.3 - Global 7.1.3 - Monitor Agent 7.0.0 - Auto Attendant 7.1.3 - Voice Mail 7.1.3 - Madrox Multi-app Support 7.1.3 - Bootloader (Secondary) 1.0.3.0 - Core 2.4.0.4 - TimeCardView 7.1.3 - GPL Infrastructure 2.2.1.1 Installed Languages: - CUE Voicemail US English 7.1.3 INIT: Sending processes the TERM signal Halting ... shutdown: sending all processes the TERM signal... rbcp: INFO rbcp daemon output END platform.config: INFO platform.config server output END trace: INFO trace daemon output END shutdown: sending all processes the KILL signal. shutdown: turning off swap shutdown: unmounting all file systems The system is haShutdown: hda lted. Press CTRLSystem halted. -ALT-DEL or turn