Smart Init is enabled
smart init is sizing iomem
  ID            MEMORY_REQ                 TYPE
0003E7          0X003DA000 C2811 Mainboard
                0X00263F50 Onboard VPN
                0X000021B8 Onboard USB
0004F4          0X00016804 Virtual Private Network (VPN) Module
                0X002C29F0 public buffer pools
                0X00211000 public particle pools
TOTAL:          0X00B2A2FC

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 12Mb.
Using 4 percent iomem. [12Mb/256Mb]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 10-Jan-08 16:35 by prod_rel_team
Image text-base: 0x400B1E74, data-base: 0x434A40E0

******   ERROR detected on PCI0 Bus
******   Try RESEATING all modules in the system
******   pci0_int_cause 0x00000200,
******   pci0_err_addr 0x00023801, pci0_err_cmd 0x0000000A
******   PCI Target Abort

r0  = FFFFFFFF r1  = FFFFFFFF r2  = 0        r3  = 45C80000 r4  = 0       
r5  = 303      r6  = 0        r7  = 0        r8  = 0        r9  = 380000  
r10 = 0        r11 = 7        r12 = 0        r13 = 465FBD8A r14 = 0       
r15 = 0        r16 = 0        r17 = C100     r18 = 0        r19 = 3400C101
r20 = 0        r21 = 40096828 r22 = FFFFFFFF r23 = FFFF00FF r24 = 0       
r25 = 469B4D74 r26 = 0        r27 = 469B4D70 r28 = 0        r29 = 469B4D6C
r30 = 0        r31 = 469B4D68 r32 = FFFFFFFF r33 = FFFFFFFF r34 = FFFFFFFF
r35 = FFFFFFFF r36 = FFFFFFFF r37 = FFFFFFFF r38 = FFFFFFFF r39 = FFFFFFFF
r40 = FFFFFFFF r41 = FFFFFFFF r42 = FFFFFFFF r43 = FFFFFFFF r44 = FFFFFFFF
r45 = FFFFFFFF r46 = FFFFFFFF r47 = FFFFFFFF r48 = 0        r49 = 469B4DC0
r50 = 0        r51 = 0        r52 = 0        r53 = 3040A801 r54 = FFFFFFFF
r55 = A000F000 r56 = FFFFFFFF r57 = FFFFFFFF r58 = 0        r59 = 465FBD78
r60 = FFFFFFFF r61 = FFFFFFFF r62 = 0        r63 = 402E4AE4
sreg     = 3400C103 mdlo_hi    = 0        mdlo        = BE00
mdhi_hi  = 0        mdhi       = 0        badvaddr_hi = FFFFFFFF
badvaddr = FFFFFFFF cause      = FFFFFFFF epc_hi      = 0
epc      = 402E4AF8 err_epc_hi = FFFFFFFF err_epc     = FFFFFFFF

%ERR-1-FATAL: Fatal error interrupt, reloading
 err_stat=0x0


=== Flushing messages (16:17:11 UTC Mon Nov 24 2008) ===

Queued messages:

 16:17:12 UTC Mon Nov 24 2008: Interrupt exception, CPU signal 22, PC = 0x0



--------------------------------------------------------------------
   Possible software fault. Upon reccurence,  please collect
   crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------


-Traceback=
$0 : 00000000, AT : 00000000, v0 : 00000000, v1 : 00000000
a0 : 00000000, a1 : 00000000, a2 : 00000000, a3 : 00000000
t0 : 00000000, t1 : 00000000, t2 : 00000000, t3 : 00000000
t4 : 00000000, t5 : 00000000, t6 : 00000000, t7 : 00000000
s0 : 00000000, s1 : 00000000, s2 : 00000000, s3 : 00000000
s4 : 00000000, s5 : 00000000, s6 : 00000000, s7 : 00000000
t8 : 00000000, t9 : 00000000, k0 : 00000000, k1 : 00000000
gp : 00000000, sp : 00000000, s8 : 00000000, ra : 00000000
EPC  : 00000000, ErrorEPC : 00000000, SREG     : 00000000
MDLO : 00000000, MDHI     : 00000000, BadVaddr : 00000000
DATA_START : 0x434A40E0
Cause 00000000 (Code 0x0): Interrupt exception

Writing crashinfo to flash:crashinfo_20081124-161713
No warm reboot Storage
*** System received a System Error ***
signal= 0x16, code= 0x0, context= 0x4691d3d8
PC = 0x40096d7c, Cause = 0x20, Status Reg = 0x34008002


System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.

Initializing memory for ECC
.
c2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled


Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80