A3#
A3#sh ip pim ne
PIM Neighbor Table
Mode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority,
      P - Proxy Capable, S - State Refresh Capable, G - GenID Capable
Neighbor          Interface                Uptime/Expires    Ver   DR
Address                                                            Prio/Mode
10.52.100.52      GigabitEthernet0/0       00:16:18/00:01:32 v2    1 / S P G
10.52.100.2       GigabitEthernet0/0       00:16:18/00:01:37 v2    1 / S P G
10.52.100.53      GigabitEthernet0/0       00:16:18/00:01:03 v2    1 / DR S P G
A3#


A3#
A3#sh ip rpf 1.1.1.1
RPF information for ? (1.1.1.1)
  RPF interface: GigabitEthernet0/0
  RPF neighbor: ? (10.52.100.51)
  RPF route/mask: 0.0.0.0/0
  RPF type: unicast (static)
  Doing distance-preferred lookups across tables
  RPF topology: ipv4 multicast base, originated from ipv4 unicast base
A3#

A3#sh ip rpf 1.1.1.2
RPF information for ? (1.1.1.2)
  RPF interface: GigabitEthernet0/0
  RPF neighbor: ? (10.52.100.51)
  RPF route/mask: 0.0.0.0/0
  RPF type: unicast (static)
  Doing distance-preferred lookups across tables
  RPF topology: ipv4 multicast base, originated from ipv4 unicast base
A3#


A3#
A3#mtrace 10.10.10.10 1.1.1.1
Type escape sequence to abort.
Mtrace from 10.10.10.10 to 1.1.1.1 via RPF
From source (?) to destination (?)
Querying full reverse path... * switching to hop-by-hop:
 0  1.1.1.1
-1  * * * Timed out receiving responses
Perhaps no local router has a route for source, the receiver is not
a member of the multicast group or the multicast ttl is too low.
A3#


A3#
A3#mtrace 10.10.10.10 1.1.1.2
Type escape sequence to abort.
Mtrace from 10.10.10.10 to 1.1.1.2 via RPF
From source (?) to destination (?)
Querying full reverse path... * switching to hop-by-hop:
 0  1.1.1.2
-1 * * * Timed out receiving responses
Perhaps no local router has a route for source, the receiver is not
a member of the multicast group or the multicast ttl is too low.

*Oct  9 08:43:03.311: PIM-BSR(0): bootstrap (1.1.1.1) on non-RPF path GigabitEthernet0/0 or from non-RPF neighbor 10.52.100.51 discarded
A3#

A3#
A3#traceroute 1.1.1.2 source loopback 0
Type escape sequence to abort.
Tracing the route to 1.1.1.2
VRF info: (vrf in name/id, vrf out name/id)
  1  *  *  *
  2  *  *  *
  3  *  *  *
  4  *  *  *
  5  *
*Oct  9 08:44:04.003: PIM-BSR(0): bootstrap (1.1.1.1) on non-RPF path GigabitEthernet0/0 or from non-RPF neighbor 10.52.100.51 discarded *  *
  6  *  *  *
  7  *  *  *
  8  *  *  *
  9  *  *  *
 10  *  *  *
 11  *  *  *
 12
*Oct  9 08:45:04.303: PIM-BSR(0): bootstrap (1.1.1.1) on non-RPF path GigabitEthernet0/0 or from non-RPF neighbor 10.52.100.51 discarded *  *  *
 13  *  *  *
 14  *  *  *
 15  *  *  *
 16  *  *  *
 17  *


A3#traceroute 1.1.1.1 source loopback 0
Type escape sequence to abort.
Tracing the route to 1.1.1.1
VRF info: (vrf in name/id, vrf out name/id)
 1  *  *  *
  2  *  *  *
  3  *  *  *
  4  *  *  *
  5  *  *  *
  6  *  *  *
  7  *  *  *
  8  *  *  *

*Oct  9 08:46:04.707: PIM-BSR(0): bootstrap (1.1.1.1) on non-RPF path GigabitEthernet0/0 or from non-RPF neighbor 10.52.100.51 discarded *
A3#

A3#
A3#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/65/76 ms
A3#

A3#
A3#ping 1.1.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 40/56/64 ms
A3#

A3#
A3#sh ip pim rp
Group: 225.1.1.1, RP: 0.0.0.0
A3#

A3#
A3#sh ip pim bsr-router
PIMv2 Bootstrap information
A3#