*Mar 2 02:25:39.946: Se1/0:23 DDR: rotor dialout [best] least recent failure is also most recent failure *Mar 2 02:25:39.946: Se1/0:23 DDR: rotor dialout [best] also has most recent fa ilure *Mar 2 02:25:39.946: Se1/0:23 DDR: rotor dialout [best] *Mar 2 02:25:39.946: Se1/0:23 DDR: Dialing cause ip (s=157.168.140.50, d=194.11 .69.186) *Mar 2 02:25:39.946: Se1/0:23 DDR: Attempting to dial 00778675525153418 *Mar 2 02:25:39.950: ISDN Se1/0:23 Q931: Applying typeplan for sw-type 0x5 is 0 x2 0x1, Called num 00778675525153418 hkgro080# *Mar 2 02:25:39.950: ISDN Se1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x018D Bearer Capability i = 0x8890 Standard = CCITT Transer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98397 Exclusive, Channel 23 Called Party Number i = 0xA1, '00778675525153418' Plan:ISDN, Type:National *Mar 2 02:25:40.090: ISDN Se1/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x81 8D Channel ID i = 0xA98397 Exclusive, Channel 23 *Mar 2 02:25:42.638: ISDN Se1/0:23 Q931: RX <- CONNECT pd = 8 callref = 0x818D *Mar 2 02:25:42.650: %LINK-3-UPDOWN: Interface Serial1/0:22, changed state to u p *Mar 2 02:25:42.654: Se1/0:22: interface must be fifo queue, force fifo *Mar 2 02:25:42.654: %DIALER-6-BIND: Interface Se1/0:22 bound to profile Di1 *Mar 2 02:25:42.654: ISDN Se1/0:23 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x 018D *Mar 2 02:25:42.766: Se1/0:22 DDR: Remote name for szxro010 *Mar 2 02:25:42.766: Se1/0:22 MLP: Request add link to bundle *Mar 2 02:25:42.766: Se1/0:22 MLP: Adding link to bundle *Mar 2 02:25:42.770: Di1 MLP: Lost frag timeout too low for slippage constraint s, increasing to 1500 ms *Mar 2 02:25:42.770: Di1 MLP: Added first link Se1/0:22 to bundle szxro010 *Mar 2 02:25:42.814: Di1 DDR: dialer protocol up *Mar 2 02:25:43.766: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0: 22, changed state to up *Mar 2 02:25:45.226: Di1: MLP: Bundle has 1/4 desired links, requesting another *Mar 2 02:25:45.226: Se1/0:23 DDR: rotor dialout [best] least recent failure is also most recent failure *Mar 2 02:25:45.226: Se1/0:23 DDR: rotor dialout [best] also has most recent fa ilure *Mar 2 02:25:45.226: Se1/0:23 DDR: rotor dialout [best] *Mar 2 02:25:45.226: Se1/0:23 DDR: Attempting to dial 00778675525153418 *Mar 2 02:25:45.226: ISDN Se1/0:23 Q931: Applying typeplan for sw-type 0x5 is 0 x2 0x1, Called num 00778675525153418 *Mar 2 02:25:45.226: ISDN Se1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x018E Bearer Capability i = 0x8890 Standard = CCITT Transer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98396 Exclusive, Channel 22 Called Party Number i = 0xA1, '00778675525153418' Plan:ISDN, Type:National *Mar 2 02:25:45.390: ISDN Se1/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x81 8E Channel ID i = 0xA98396 Exclusive, Channel 22 *Mar 2 02:25:47.886: ISDN Se1/0:23 Q931: RX <- CONNECT pd = 8 callref = 0x818E *Mar 2 02:25:47.898: %LINK-3-UPDOWN: Interface Serial1/0:21, changed state to u p *Mar 2 02:25:47.902: Se1/0:21: interface must be fifo queue, force fifo *Mar 2 02:25:47.902: %DIALER-6-BIND: Interface Se1/0:21 bound to profile Di1 *Mar 2 02:25:47.902: %ISDN-6-CONNECT: Interface Serial1/0:22 is now connected t o 00778675525153418 szxro010 *Mar 2 02:25:47.902: ISDN Se1/0:23 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x 018E *Mar 2 02:25:48.014: Se1/0:21 DDR: Remote name for szxro010 *Mar 2 02:25:48.014: Se1/0:21 MLP: Request add link to bundle *Mar 2 02:25:48.014: Se1/0:21 MLP: Adding link to bundle *Mar 2 02:25:48.014: Di1 MLP: Lost frag timeout too low for slippage constraint s, increasing to 1500 ms *Mar 2 02:25:48.014: Di1 MLP: Added link Se1/0:21 to bundle szxro010 *Mar 2 02:25:49.014: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0: 21, changed state to up *Mar 2 02:25:49.226: Di1: MLP: Bundle has 2/4 desired links, requesting another *Mar 2 02:25:49.226: Se1/0:23 DDR: rotor dialout [best] least recent failure is also most recent failure *Mar 2 02:25:49.226: Se1/0:23 DDR: rotor dialout [best] also has most recent fa ilure *Mar 2 02:25:49.226: Se1/0:23 DDR: rotor dialout [best] *Mar 2 02:25:49.226: Se1/0:23 DDR: Attempting to dial 00778675525153418 *Mar 2 02:25:49.226: ISDN Se1/0:23 Q931: Applying typeplan for sw-type 0x5 is 0 x2 0x1, Called num 00778675525153418 *Mar 2 02:25:49.226: ISDN Se1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x018F Bearer Capability i = 0x8890 Standard = CCITT Transer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98395 Exclusive, Channel 21 Called Party Number i = 0xA1, '00778675525153418' Plan:ISDN, Type:National *Mar 2 02:25:49.338: ISDN Se1/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x81 8F Channel ID i = 0xA98395 Exclusive, Channel 21 *Mar 2 02:25:51.442: ISDN Se1/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x8 18F Cause i = 0x839F - Normal, unspecified *Mar 2 02:25:51.442: %ISDN-6-CONNECT: Interface Serial1/0:21 is now connected t o 00778675525153418 szxro010 *Mar 2 02:25:51.462: ISDN Se1/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x018F *Mar 2 02:25:51.486: ISDN Se1/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0 x818F *Mar 2 02:25:51.490: Serial1/0:23: wait for isdn carrier timeout, call id=0x819 2ter no mon