RO01#conf t Enter configuration commands, one per line. End with CNTL/Z. RO01(config)#no ip routing RO01(config)#bridge 1 protocol ieee RO01(config)#default interface Fas0 Interface FastEthernet0 set to default configuration RO01(config)#interface Fas0 RO01(config-if)#Description Interface to Firewall RO01(config-if)#no switchport % Incomplete command. RO01(config-if)#no switchport ? access Set access mode characteristics of the interface mode Set trunking mode of the interface priority Set 802.1p priorities protected Configure an interface to be a protected port trunk Set trunking characteristics of the interface voice Voice appliance attributes RO01(config-if)#no switchport mode ? RO01(config-if)#no switchport mode RO01(config-if)#no ip ipaddress ^ % Invalid input detected at '^' marker. RO01(config-if)#no ip ? Interface IP configuration subcommands: address Set the IP address of an interface ddns Configure dynamic DNS dhcp Configure DHCP parameters for this interface RO01(config-if)#no ip address RO01(config-if)#no route-cache ^ % Invalid input detected at '^' marker. RO01(config-if)#no ? aaa Authentication, Authorization and Accounting. arp Set arp type (arpa, probe, snap) or timeout or log options backup Modify backup parameters bandwidth Set bandwidth informational parameter bfd BFD interface configuration commands bgp-policy Apply policy propagated by bgp community string bridge-group Transparent bridging interface parameters carrier-delay Specify delay for interface transitions cdp CDP interface subcommands cmns OSI CMNS crypto Encryption/Decryption commands dampening Enable event dampening delay Specify interface throughput delay description Interface specific description dot1q dot1q interface configuration commands dot1x Interface Config Commands for IEEE 802.1X duplex Configure duplex operation. eou EAPoUDP Interface Configuration Commands ethernet Ethernet interface parameters flow-sampler Attach flow sampler to the interface history Interface history histograms - 60 second, 60 minute and 72 hour hold-queue Set hold queue depth ip Interface Internet Protocol config commands iphc-profile Configure IPHC profile keepalive Enable keepalive llc2 LLC2 Interface Subcommands load-interval Specify interval for load calculation for an interface logging Configure logging for interface mac-address Manually set interface MAC address macro Command macro max-reserved-bandwidth Maximum Reservable Bandwidth on an Interface mtu Set the interface Maximum Transmission Unit (MTU) netbios Use a defined NETBIOS access list or enable name-caching ntp Configure NTP pppoe pppoe interface subcommands pppoe-client pppoe client rmon Configure Remote Monitoring on an interface routing Per-interface routing configuration service-policy Configure QoS Service Policy shutdown Shutdown the selected interface snapshot Configure snapshot support on the interface snmp Modify SNMP interface parameters source Get config from another source spanning-tree Spanning Tree Subsystem speed Configure speed operation. storm-control storm configuration switchport Set switching mode characteristics timeout Define timeout values for this interface topology Configure routing topology on the interface transmit-interface Assign a transmit interface to a receive-only interface tx-ring-limit Configure PA level transmit ring limit waas WAN Optimization xconnect Xconnect commands zone-member Apply zone name RO01(config-if)#interface fas0/0.10 ^ % Invalid input detected at '^' marker. RO01(config)#interface fas0? . : <0-3> RO01(config)#interface fas0/ ^ % Invalid input detected at '^' marker. RO01(config)#interface fas0.10 ^ % Invalid input detected at '^' marker. RO01(config)#interface ? ATM ATM interface Async Async interface Auto-Template Auto-Template interface BVI Bridge-Group Virtual Interface CDMA-Ix CDMA Ix interface CTunnel CTunnel interface Dialer Dialer interface Ethernet IEEE 802.3 FastEthernet FastEthernet IEEE 802.3 Group-Async Async Group interface Lex Lex interface LongReachEthernet Long-Reach Ethernet interface Loopback Loopback interface Multilink Multilink-group interface Null Null interface Tunnel Tunnel interface Vif PGM Multicast Host interface Virtual-PPP Virtual PPP interface Virtual-Template Virtual Template interface Virtual-TokenRing Virtual TokenRing Vlan Vlan IEEE 802.1q range interface range command vmi Virtual Multipoint Interface RO01(config)#interface fas0 /0.10 ^ % Invalid input detected at '^' marker. RO01(config)#interface fas0 0.10 ^ % Invalid input detected at '^' marker. RO01(config)#interface fas 0/0.10 ^ % Invalid input detected at '^' marker. RO01(config)#interface fa0 0/0.10 ^ % Invalid input detected at '^' marker. RO01(config)#interface fa0 RO01(config-if)#show ^ % Invalid input detected at '^' marker. RO01(config-if)#show int fas0 ^ % Invalid input detected at '^' marker. RO01(config-if)#^Z %SYS-5-CONFIG_I: Configured from console by console RO01#sh fas0 ^ % Invalid input detected at '^' marker. RO01#sh int fas0 FastEthernet0 is up, line protocol is down Hardware is Fast Ethernet, address is MAC### (bia MAC###) Description: Interface to Firewall MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set RO01#sh int fas0 brief ^ % Invalid input detected at '^' marker. RO01#conf t Enter configuration commands, one per line. End with CNTL/Z. RO01(config)#interface Ethernet0.10 RO01(config-subif)#encapsulation dot1q 10 RO01(config-subif)#no ip address RO01(config-subif)#no ip route-cache RO01(config-subif)#>>bridge-group 1 ^ % Invalid input detected at '^' marker. RO01(config-subif)#bridge-group 1 RO01(config-subif)#interface Vlan1 RO01(config-if)#no ip address RO01(config-if)#ip virtual-reassembly in RO01(config-if)#no ip route-cache RO01(config-if)#bridge-group 1 RO01(config-if)#^Z RO01# %SYS-5-CONFIG_I: Configured from console by console RO01# RO01#show running-config see above RO01#