Voip enable E3000

imikerae0 — Fri, 26 Aug 2011 06:52:31 GMT

My name is Mike Rae and I am trying to get Voip working via Pennytel here in Australia.

I have the following setup:

Modem: Siemens Speedstream 4200 that signs on to Bigppnd ISP and passes an IP address to the router. DMZ is disabled.

Router: Cisco E3000 with Firewall disabled and ports 5060-5061 port forwarded to the ATA.

Cisco PAP2T ATA: Setup to Pennytel specs.

Problem:

I can receive calls. When I do I there is no incoming voice but the caller can hear me.

I cannot call out. There are no error messages, only silence and after a time the repetitive beeps of timing out.

Request:

I think the problem is in the E3000 setup? The Modem does very little and the ATA is setup to Pennytel specs. Can anyone help with areas or settings I should look at? I would be grateful for any advice.

ATA settings follow:

Voice

Phone Adapter with 2 Ports for Voice-Over-IP

PAP2

Info

System

SIP

Provisioning

Regional

Line 1

Line 2

User 1

User 2

Advanced View (switch to basic view)

User Login

System Information
	DHCP:	Enabled	Current IP:	192.168.1.145
	Host Name:	LinksysPAP	Domain:	BigPond
	Current Netmask:	255.255.255.0	Current Gateway:	192.168.1.1
	Primary DNS:	10.0.0.138
	Secondary DNS:	192.168.1.1
Product Information
	Product Name:	PAP2T	Serial Number:	FL18H5081895
	Software Version:	5.1.6(LS)	Hardware Version:	5.1.5
	MAC Address:	0014BF8F1895	Client Certificate:	Installed
	Customization:	Open
System Status
	Current Time:	8/25/2011 22:49:31	Elapsed Time:	1 day and 00:50:24
	Broadcast Pkts Sent:	0	Broadcast Bytes Sent:	0
	Broadcast Pkts Recv:	583439	Broadcast Bytes Recv:	35404833
	Broadcast Pkts Dropped:	0	Broadcast Bytes Dropped:	0
	RTP Packets Sent:	0	RTP Bytes Sent:	0
	RTP Packets Recv:	0	RTP Bytes Recv:	0
	SIP Messages Sent:	87	SIP Bytes Sent:	62850
	SIP Messages Recv:	67	SIP Bytes Recv:	30996
	External IP:
Line 1 Status
	Display Name:	8889333168	User ID:	8889333168
	Hook State:	On	Registration State:	Online
	Last Registration At:	8/25/2011 22:46:55	Next Registration In:	3414 s
	Message Waiting:	No	Call Back Active:	No
	Last Called Number:		Last Caller Number:	0755915037
	Mapped SIP Port:
	Call 1 State:	Idle	Call 2 State:	Idle
	Call 1 Tone:	None	Call 2 Tone:	None
	Call 1 Encoder:		Call 2 Encoder:
	Call 1 Decoder:		Call 2 Decoder:
	Call 1 FAX:		Call 2 FAX:
	Call 1 Type:		Call 2 Type:
	Call 1 Remote Hold:		Call 2 Remote Hold:
	Call 1 Callback:		Call 2 Callback:
	Call 1 Peer Name:		Call 2 Peer Name:
	Call 1 Peer Phone:		Call 2 Peer Phone:
	Call 1 Duration:		Call 2 Duration:
	Call 1 Packets Sent:		Call 2 Packets Sent:
	Call 1 Packets Recv:		Call 2 Packets Recv:
	Call 1 Bytes Sent:		Call 2 Bytes Sent:
	Call 1 Bytes Recv:		Call 2 Bytes Recv:
	Call 1 Decode Latency:		Call 2 Decode Latency:
	Call 1 Jitter:		Call 2 Jitter:
	Call 1 Round Trip Delay:		Call 2 Round Trip Delay:
	Call 1 Packets Lost:		Call 2 Packets Lost:
	Call 1 Packet Error:		Call 2 Packet Error:
	Call 1 Mapped RTP Port:		Call 2 Mapped RTP Port:
	Call 1 Media Loopback:		Call 2 Media Loopback:

Voip enable E3000

imikerae0 — Sun, 28 Aug 2011 22:33:03 GMT

I have discovered that the Siemens modem provided by Telstra blocks port 5060. This disables VoiP. I am going to replace the modem. Any suggestions?

topic Voip enable E3000 in IP Telephony and Phones

Voip enable E3000

Voice

Voip enable E3000