topic Re: ACE context syslog in Application Networking

ACE context syslog

celiocarreto — Tue, 16 Dec 2008 10:05:58 GMT

Hi!

Does someone know how to configure the syslog under a context?

The syslog should be send via public interface. No additional management interface should be configured.

Any ideas?

Re: ACE context syslog

dario.didio — Tue, 16 Dec 2008 12:40:27 GMT

Hi,

you can configure syslog under each context separatly.

Please refer to following document.

http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA1_7_/configuration/system/message/guide/config.html#wp1059844

Normally, the ACE will use its public interface due to its routing table (default route is pointing to public interface)

Hope this helps!

Re: ACE context syslog

celiocarreto — Tue, 16 Dec 2008 13:13:29 GMT

I configured it as described in the manual.

In the Admin context it works. In a sub-context not. No Packets are sent by the ACE appliance.

Any other ideas or working configurations?

Re: ACE context syslog

dario.didio — Tue, 16 Dec 2008 13:17:31 GMT

I'm using it in different contexts and it works fine.

can you upload your config?

Re: ACE context syslog

celiocarreto — Tue, 16 Dec 2008 13:58:44 GMT

The configuration is basicly:

logging enable

logging fastpath

logging console 1

logging timestamp

logging buffered 5

logging persistent 6

logging monitor 5

logging facility 21

logging queue 1024

logging device-id context-name

logging host 195.122.17.210 udp/514

logging rate-limit 42 60 level 5

logging rate-limit 42 60 level 6

logging rate-limit 42 60 level 7

access-list V101-IN line 1 extended permit icmp 195.122.1.0 255.255.255.0 195.

122.1.0 255.255.255.0

access-list V101-IN line 2 extended permit icmp any host 195.122.1.6

access-list V101-IN line 3 extended permit icmp any host 195.122.1.5

access-list V101-IN line 10 extended permit icmp any host 195.122.1.17

access-list V101-IN line 20 extended permit icmp any host 195.122.1.18

access-list V101-IN line 30 extended permit icmp any host 195.122.1.19

access-list V101-IN line 40 extended permit tcp any host 195.122.1.17 eq www

access-list V101-IN line 50 extended permit tcp any host 195.122.1.18 eq www

access-list V101-IN line 60 extended permit tcp any host 195.122.1.19 eq www

access-list V101-IN line 68 extended permit tcp any host 195.122.1.17 eq https

interface vlan 3

description WL-Server-Frontend

ip address 10.125.145.253 255.255.255.0

alias 10.125.145.254 255.255.255.0

peer ip address 10.125.145.252 255.255.255.0

service-policy input ICMP-ALLOW

no shutdown

interface vlan 101

description outside

ip address 195.122.1.5 255.255.255.0

alias 195.122.1.6 255.255.255.0

peer ip address 195.122.1.4 255.255.255.0

access-group input V101-IN

service-policy input L4-V101-LB

no shutdown

ip route 0.0.0.0 0.0.0.0 195.122.1.1

Re: ACE context syslog

dario.didio — Tue, 16 Dec 2008 14:09:09 GMT

Can you configure for example:

logging trap 6

This specifies that messages between 0-6 are send to the syslog server specified by the "logging host" command.

I don't know which severity is the default value.

Re: ACE context syslog

celiocarreto — Tue, 16 Dec 2008 15:05:52 GMT

Great it works!!

Many THX!

Re: ACE context syslog

dario.didio — Tue, 16 Dec 2008 15:38:59 GMT

your welcome, thanks for the rating