topic Re: CSS 11500 not working in Application Networking https://community.cisco.com/t5/application-networking/css-11500-not-working/m-p/283486#M4293 <HTML><HEAD></HEAD><BODY><P>show phy</P><P>show circuit</P><P></P><P>verify that status of the physical link.</P><P></P><P>show arp</P><P>make sure you have aro entries for the servers and gateways.</P><P></P><P>Finally, if you are reusing the same ip addresses, make sure to clear the arp table of the servers and gateways.</P><P></P><P>Regards,</P><P></P><P>Gilles.</P></BODY></HTML> Tue, 27 Jul 2004 11:50:10 GMT Gilles Dufour 2004-07-27T11:50:10Z CSS 11500 not working https://community.cisco.com/t5/application-networking/css-11500-not-working/m-p/283485#M4292 <P>I replicated the configurations on CSS 11050 box on a new CSS 11500. The configuration is shown below</P><P></P><P></P><P></P><P> ip redundancy master</P><P></P><P> </P><P></P><P> ip route 0.0.0.0 0.0.0.0 192.168.2.2 1</P><P></P><P> </P><P>!************************* INTERFACE *************************</P><P>interface e1</P><P> phy 100Mbits-FD</P><P> bridge vlan 113</P><P> description "Connection to DMZ VLAN113"</P><P></P><P>interface e2</P><P> phy 100Mbits-FD</P><P> bridge vlan 114</P><P> description "Connection to DMZCSS VLAN114"</P><P></P><P>interface e3</P><P> phy 100Mbits-FD</P><P></P><P>interface e4</P><P> phy 100Mbits-FD</P><P></P><P>interface e5</P><P> phy 100Mbits-FD</P><P></P><P>interface e6</P><P> phy 100Mbits-FD</P><P></P><P>interface e7</P><P> phy 100Mbits-FD</P><P></P><P>interface e8</P><P> phy 100Mbits-FD</P><P> bridge vlan 99</P><P> </P><P>!************************** CIRCUIT **************************</P><P>circuit VLAN113</P><P></P><P> ip address 192.168.2.20 255.255.255.0</P><P></P><P>circuit VLAN114</P><P></P><P> ip address 192.168.4.1 255.255.255.0</P><P></P><P></P><P>!************************** SERVICE **************************</P><P>service ba1</P><P> ip address 192.168.4.5</P><P> keepalive type tcp</P><P> active</P><P></P><P>service ba2</P><P> ip address 192.168.4.6</P><P> keepalive type tcp</P><P> active</P><P></P><P>service cmsprod1</P><P> ip address 192.168.4.9</P><P> keepalive type tcp</P><P> active</P><P></P><P>service cmsprod2</P><P> ip address 192.168.4.10</P><P> keepalive type tcp</P><P> active</P><P></P><P>service daaw1</P><P> keepalive type tcp</P><P> ip address 192.168.4.19</P><P> active</P><P></P><P>service daaw2</P><P> ip address 192.168.4.20</P><P> keepalive type tcp</P><P> active</P><P></P><P></P><P>!*************************** OWNER ***************************</P><P>owner BA</P><P></P><P> content wwwba</P><P> vip address 192.168.2.225</P><P> add service ba1</P><P> add service ba2</P><P> advanced-balance sticky-srcip</P><P> protocol tcp</P><P> port 80</P><P> active</P><P></P><P>owner BA-ssl</P><P></P><P> content wwwba-ssl</P><P> add service ba1</P><P> add service ba2</P><P> advanced-balance sticky-srcip</P><P> protocol tcp</P><P> port 443</P><P> vip address 192.168.2.225</P><P> active</P><P></P><P>owner CMS</P><P></P><P> content wwwcms</P><P> vip address 192.168.2.186</P><P> add service cmsprod2</P><P> protocol tcp</P><P> port 80</P><P> advanced-balance sticky-srcip</P><P> add service cmsprod1</P><P> active</P><P></P><P>owner DAA</P><P></P><P> content daaweb</P><P> add service daaw1</P><P> add service daaw2</P><P> advanced-balance sticky-srcip</P><P> protocol tcp</P><P> port 80</P><P> vip address 192.168.4.41</P><P> active</P><P></P><P>!*************************** GROUP ***************************</P><P>group BA</P><P> vip address 192.168.2.225</P><P> add service ba1</P><P> add service ba2</P><P> active</P><P></P><P>group CMS</P><P> vip address 192.168.2.186</P><P> add service cmsprod1</P><P> add service cmsprod2</P><P> active</P><P></P><P>group DAA</P><P> add service daaw1</P><P> add service daaw2</P><P> vip address 192.168.4.41</P><P> active</P><P></P><P>I am trying to replace the existing 11050 already in production with this new 11500 with the same config but it is not working. when I did "sh service summary" all the services were down when I put the new box into production and I couldnt even ping my default gateway. I wasnt also able to ping any of the services addresses. Is there something am doing wrong..pls help. </P><P></P><P> By the way, the existing 11050 has the same config and it is working perfectly</P> Tue, 27 Jul 2004 10:06:20 GMT https://community.cisco.com/t5/application-networking/css-11500-not-working/m-p/283485#M4292 m_adetunji 2004-07-27T10:06:20Z Re: CSS 11500 not working https://community.cisco.com/t5/application-networking/css-11500-not-working/m-p/283486#M4293 <HTML><HEAD></HEAD><BODY><P>show phy</P><P>show circuit</P><P></P><P>verify that status of the physical link.</P><P></P><P>show arp</P><P>make sure you have aro entries for the servers and gateways.</P><P></P><P>Finally, if you are reusing the same ip addresses, make sure to clear the arp table of the servers and gateways.</P><P></P><P>Regards,</P><P></P><P>Gilles.</P></BODY></HTML> Tue, 27 Jul 2004 11:50:10 GMT https://community.cisco.com/t5/application-networking/css-11500-not-working/m-p/283486#M4293 Gilles Dufour 2004-07-27T11:50:10Z Re: CSS 11500 not working https://community.cisco.com/t5/application-networking/css-11500-not-working/m-p/283487#M4294 <HTML><HEAD></HEAD><BODY><P>Thanks Gilles. It eventually worked. It was VLAN issue and I resolved it.</P></BODY></HTML> Mon, 02 Aug 2004 14:16:58 GMT https://community.cisco.com/t5/application-networking/css-11500-not-working/m-p/283487#M4294 m_adetunji 2004-08-02T14:16:58Z