WAVE-274 Rescue CD-ROM

manugomeza — Sat, 11 Aug 2012 03:02:09 GMT

Dear Team,

I was trying to rescue a WAVE-274 from the rescue CD, I downloaded the ISO image 4.5.1 (waas-rescue-cdrom-4.5.1.2-k9),

and I followed the procedure: first #2 to format the Flash, then #3 to copy the cookie, then #5 to copy de sysimg from the

cdrom, and then #8 to copy the image (.img) to local disk.

But I have a problem when run the step 8, the WAVE-274 does not boot from flash:

The message said:

MODEL: OE274

FLASH: found, directory validated, version 1

COOKIE: valid

IMAGE: NONE

FLASHDEV: /dev/sdb

Installer Main Menu:

1. Configure Network

2. Manufacture flash

3. Install flash cookie

4. Install flash image from network

5. Install flash image from usb/cdrom

6. Install flash image from disk

7. Recreate RAID device (WAE-674/7341/7371/7541/7571/8541 only)

8. Wipe out disks and install .bin image

9. Exit (reboot)

Choice [0]: 3

Date= '08/10/12'

Cookie installed successfully.

MODEL: OE274

FLASH: found, directory validated, version 1

COOKIE: valid

IMAGE: NONE

FLASHDEV: /dev/sdb

Installer Main Menu:

1. Configure Network

2. Manufacture flash

3. Install flash cookie

4. Install flash image from network

5. Install flash image from usb/cdrom

6. Install flash image from disk

7. Recreate RAID device (WAE-674/7341/7371/7541/7571/8541 only)

8. Wipe out disks and install .bin image

9. Exit (reboot)

Choice [0]: 5

Using cd-rom device (/dev/scd0)

Please select an image from the following list:

1. waas-x86_64-4.5.1.2-k9.sysimg

2. Return to Main Menu

Image [1]: 1

Using image waas-x86_64-4.5.1.2-k9.sysimg

Read 26975232 byte image file

Existing version in flash: NONE

New version to install: 4.5.1.2

Proceed with flash write? [y]: y

.............................................................................................................................................................................................................. done.

Image was successfully written to flash.

unmount device (/dev/scd0)

MODEL: OE274

FLASH: found, directory validated, version 1

COOKIE: valid

IMAGE: 4.5.1.2

FLASHDEV: /dev/sdb

Installer Main Menu:

1. Configure Network

2. Manufacture flash

3. Install flash cookie

4. Install flash image from network

5. Install flash image from usb/cdrom

6. Install flash image from disk

7. Recreate RAID device (WAE-674/7341/7371/7541/7571/8541 only)

8. Wipe out disks and install .bin image

9. Exit (reboot)

Choice [0]: 8

Using cd-rom device (/dev/scd0)

Enter full URL of .bin image to install.

ftp://[user:pass@]ip_addr/path/to/file

http://[user:pass@]ip_addr/path/to/file

file:/local/path/to/to/file

URL for .bin image [file:/media/images/waas-universal-4.5.1.2-k9.bin]:

Continue? This will wipe out all disks! [n]: y

unmount device (/dev/scd0)

Scrogging sda done

Saving random seed...

dd: opening `/state/random-seed': No such file or directory

Missing system-use partitions; creating them on disk00

+ /sbin/sfdisk -f -uS /dev/sda

Found No SYSFS partition on /dev/sda, create it now.

Disk disk00: removing old disk partitions ...

Disk disk00: applying new partitioning scheme ...

Creating filesystem on device [/dev/sda1]...

e2fsck 1.38 (30-Jun-2005)

Mounting [/dev/sda1] at [/sw]

Mounted /dev/sda1 to /sw

Creating filesystem on device [/dev/sda2]...

e2fsck 1.38 (30-Jun-2005)

Mounting [/dev/sda2] at [/swstore]

Mounted /dev/sda2 to /swstore

Creating filesystem on device [/dev/sda3]...

e2fsck 1.38 (30-Jun-2005)

Mounting [/dev/sda3] at [/state]

Mounted /dev/sda3 to /state

Creating filesystem on device [/dev/sda6]...

e2fsck 1.38 (30-Jun-2005)

Mounting [/dev/sda6] at [/local/local1]

Mounted /dev/sda6 to /local/local1

Fail to open startup.config file.

Creating filesystem on device [/dev/data1/vbsp]...

Internal error: Unable to connect to dataserver

Disk encryption feature is disabled.

Internal error: Unable to connect to dataserver

Disk encryption feature is disabled.

Fail to open startup.config file.

Creating filesystem on device [/dev/data1/spool]...

Creating filesystem on device [/dev/data1/obj]...

Creating filesystem on device [/dev/data1/dre]...

Creating filesystem on device [/dev/data1/ackq]...

Creating filesystem on device [/dev/data1/plz]...

Fail to open startup.config file.

Running pre-disk-ready hooks...

connect: No such file or directory

Return value: -1

ssmgr: short read: 0 bytes

ssmgr: bad magic

ssmgr: op_open or media_open

ssmgr: short read: 0 bytes

ssmgr: bad magic

ssmgr: safe state area manufactured successfully.

Reading and installing image, it may take a few minutes, please wait...

Using cd-rom device (/dev/scd0)

remote size / mtime: 294921174 / 1321976995

Reclaiming unused flash safe state sectors ...SSMGR RETURNING: 4 (Success)

Done.

#####################################################################################

##########################

294921174 bytes transferred in 63.4 seconds (4.44 MBps)

Detected OE274

Installing phase3 bootloader...

Installing WAE 64-bit image.

Installing system image to flash... ...........................................................................................................................................

................................................................... done.

The new software will run after you reload.

Installing application components...[ac] [ap] [di] [jr] [kv] [li] [li] [me] [pe] [po] [to] [to] [un] [vm] [vm]

Running post-install hooks...

Syncing filesystems...

/ruby/bin/install-to-sw: DONE.

Successfully installed product image.

unmount device (/dev/scd0)

MODEL: OE274

FLASH: found, directory validated, version 1

COOKIE: valid

IMAGE: 4.5.1.b2

FLASHDEV: /dev/sdb

Installer Main Menu:

1. Configure Network

2. Manufacture flash

3. Install flash cookie

4. Install flash image from network

5. Install flash image from usb/cdrom

HP Remote Console 04.00age from disk

Remote Console display bypassed, System in video mode = 02 (50,18))

8. Wipe out disks and install .bin image (done)

9. Exit (reboot)

Choice [0]: 9

Reboot? [n]: y

Saving random seed...

1+0 records in

1+0 records out

unmounting /vbspace... done

unmounting /swstore... done

unmounting /sw... done

unmounting /state... done

unmounting /plz1... done

unmounting /obj1... done

unmounting /local/local1/spool... done

unmounting /local/local1... done

unmounting /dre1... done

unmounting /ackq1... done

Deactivating volume group... 0 logical volume(s) in volume group "data1" now active

done

Restarting system.

3072 MB

WAVE-274-K9 V01

BIOS Version vB1.05 08/01/08

For boot menu, press <F9> - Remote users: use Integrated Administrator

For setup, press <F10> - Remote console users press ESC+0

To boot from network, press <F12> - Remote users: use Integrated Administrator

Attempting Boot From CD-ROM

Attempting Boot From Hard Drive

I appreciate any information.

Thanks.

WAVE-274 Rescue CD-ROM

Felix Arrieta — Sun, 12 Aug 2012 17:02:37 GMT

I think you got the wrong image, when you go to download the software again make sure it looks exactly like this;

The Rescue CDROM ISO

waas-rescue-cdrom-x.x.xk9.iso

cheers

WAVE-274 Rescue CD-ROM

manugomeza — Tue, 14 Aug 2012 01:11:10 GMT

Hi Felix,

Thanks for your answer, but I am completely sure I downloaded the right image because the file says

waas-rescue-cdrom-4.5.1.2-k9.iso then I burned it to CD and finally I put it to the WAVE. But, I still have the same problem.

I appreciate any information

Manuel

WAVE-274 Rescue CD-ROM

Felix Arrieta — Wed, 15 Aug 2012 17:06:16 GMT

hello Manuel,

Please open a TAC case for replacing that box.

regards,

WAVE-274 Rescue CD-ROM

manugomeza — Thu, 23 Aug 2012 22:56:04 GMT

Ok Felix

Thanks for your time.

Regards

Manuel

topic WAVE-274 Rescue CD-ROM in Application Networking

WAVE-274 Rescue CD-ROM

WAVE-274 Rescue CD-ROM

WAVE-274 Rescue CD-ROM

WAVE-274 Rescue CD-ROM

WAVE-274 Rescue CD-ROM