topic Re: css 11150 not communicating in Application Networking

css 11150 not communicating

john.jennings — Tue, 19 Jul 2005 14:16:30 GMT

Problem: Not able to communicate (ping,telnet,http etc) from the css box to anywhere outside. Neither to the servers nor to the machines on the public ip.

Arp entries shows blank.

The interface of the switch and css shows up status.

The following are the config on the css box.

sh run

!Generated on 07/14/2005 14:24:03

!Active version: ap0610405

configure

!*************************** GLOBAL ***************************

no restrict web-mgmt

host dc1css11 xxx.yyy.zzz.ab

!************************* INTERFACE *************************

interface e11

bridge vlan 199

interface e12

bridge vlan 144

!************************** SERVICE **************************

service cnetweb01

ip address 192.168.144.172

keepalive type http

active

service cnetweb02

ip address 192.168.144.173

keepalive type http

active

!*************************** OWNER ***************************

owner webuser

content webservers

protocol tcp

port 80

add service cnetweb01

add service cnetweb02

vip address xxx.yyy.zzz.aa

active

CSS11150# exit

CSS11150#

Disconnected...

Internet

Firewall

| vlan x

Switch -------CSS 11150

| | |

| ----------

| vlan y (dmz)

svr1, svr2 (dmz)

A public vlan is created on the css11150 and a public ip is given as the VIP. Also a private vlan is assigned so as to communicate with the servers that are in the dmz zone.

Can anyone pls advice on any configuration errors on this.

Thanks,

Melvin

Re: css 11150 not communicating

Gilles Dufour — Tue, 19 Jul 2005 15:28:09 GMT

Melvin,

try to set the duplex and speed manually on both the switch and the CSS.

On the CSS the command is "phy ..."

Regards,

Gilles.

Re: css 11150 not communicating

john.jennings — Tue, 19 Jul 2005 16:02:12 GMT

Hi Gilles,

I tried with 100mbps full/half duplex and 10mbps full/half duplex on the switch as well as on the css 11150. The interface shows up. But the servers are not reachable.

And the interface comes up only with a cross cable.

Thanks,

Melvin

Re: css 11150 not communicating

john.jennings — Tue, 19 Jul 2005 17:06:17 GMT

Could this be a hardware problem? Can we confirm this by any means? I did show chassis and following is the output.

Name: CSS 11150 SW Version: 6.10 Build 405

HW Major Version: A0 HW Minor Version: 0

Serial Number: PL506040290

Base Mac Address: 00-08-e2-11-9b-eb

Module Number Module Name Status

1 FEM primary

2 GENIC primary

5 SCFM-PLUS primary

Port Number Port Name Status

1 e1 offline-bad

2 e1 offline-bad

3 e1 offline-bad

4 e1 offline-bad

5 e1 offline-bad

6 e1 offline-bad

7 e1 offline-bad

8 e1 offline-bad

9 e9 online

10 e10 online

11 e11 online

12 e12 online

13 e13 online

14 e14 online

Any updates.. greatly appriciated.

Thanks,

Melvin

Re: css 11150 not communicating

Gilles Dufour — Wed, 20 Jul 2005 07:11:24 GMT

Melvin,

indeed the "offline-bad" is a bad sign.

Can you try a 'reboot_diags'.

Save the boot sequence. We might need it.

If that does not solve the problem, you will need to replace this CSS.

Thanks,

Gilles.

Re: css 11150 not communicating

melvinsebastian — Wed, 20 Jul 2005 15:07:18 GMT

Thank you Gilles

I tried the reboot_diags. I'm afraid it didnt have much effect on the box.

I get the following msgs while booting up the css box.