topic How to configurate dynamic load balance on two VRF in a physical in MPLS

How to configurate dynamic load balance on two VRF in a physical MPLS link?

benzhao98 — Thu, 24 May 2012 06:07:45 GMT

Hi all,

would someone can tell me how to configurate dynamic load balance on two VRF in a physical MPLS link?

Topology:

HQ(3845)-----------MPLS link(2M)-----------Branch(2811)

Scene：

there a MPLS VPN link between HQ and Branch, we want to set up two VRF on this MPLS link, one is VRF-internal, another is VRF-guest, and two VRF share with 2M, can we dynamic load balance on both VRF? but VRF-internal have high priority.

Thanks

Ben

How to configurate dynamic load balance on two VRF in a physical

Mahesh Gohil — Fri, 25 May 2012 10:43:04 GMT

Hi,

Can you elaborate more on what is needed.

Is it like you have one physical link from HQ to provider (same setup at branch) and you want it split into two vrf's and then

load share between these two vrf's ?

Regards # Mahesh

How to configurate dynamic load balance on two VRF in a physical

benzhao98 — Tue, 05 Jun 2012 08:33:28 GMT

Hi Mahesh,

thanks a lot for your reply, you are right, is there any good suggestion and example configuration? and if do this, it mean there is a PE router in client network? because VRF can't be configure in CE Router? is this right?

thanks

Ben

How to configurate dynamic load balance on two VRF in a physical

shivjain — Tue, 05 Jun 2012 08:49:49 GMT

you can acheive by using vrf lite at customer end or create two sub interface one for internal and one for guest and corresponding different vrf will be terminated at PE router.

HQ(3845)---vrf lite a,b(vlan10,20)----vrf a,b(vlan10,20)----MPLS link(2M)-----------Branch(2811)

HQ(3845)---(vlan10,20)----vrf a,b(vlan10,20)----MPLS link(2M)-----------Branch(2811)

regards

Shivlu Jain

How to configurate dynamic load balance on two VRF in a physical

benzhao98 — Tue, 05 Jun 2012 09:15:00 GMT

HI Shivlu Jain,

thanks for your support, I am a learner on MPLS, Would you show me some simple example configuration(include 3845,2811 and both PE of service provider). and can we dynamic load balance on both VRF or sub interface with some QOS?

maybe the topology need change to below?

HQ3845(vrf lite a,b(vlan10,20)----PE1 (vrf a,b(vlan10,20))----MPLS link(2M)-----------PE2 (vrf a,b(vlan10,20))——--Branch2811（vrf lite a,b(vlan10,20)）

HQ3845(vlan10,20)----PE1 (vrf a,b(vlan10,20))----MPLS link(2M)-----------PE2(vrf a,b(vlan10,20))——Branch2811(vlan10,20)

How to configurate dynamic load balance on two VRF in a physical

jki — Wed, 06 Jun 2012 07:41:51 GMT

is below topology available for this requirement?

CE1(VRF-lite Guest on tunnel 0, VRF-lite-Employee on tunne1)——MPLS——CE2(VRF-lite Guest on tunnel 0, VRF-lite-Employee on tunne1)

because local SP don't accept make any change on PE router.

How to configurate dynamic load balance on two VRF in a physical

marciobaesse — Thu, 21 Jun 2012 18:23:24 GMT

Hi.

How are you today?

I looked at this topic only today, and I had a doubt.

I have two mpls links and want to do load balancing between the two links.

You say you can not change the settings of routers feet, this is correct ... but how can I ensure that the packets passed through the MPLS cloud and arrived at the destination if they go by different routes or the PEs are not the same, my SP will not know what I'm doing this.

My Local network ----- PE Router ----- cloud mpls ------ Router PE ----- My site network

By understanding, I need lith VRFs on my local network. this is correct?

How to configurate dynamic load balance on two VRF in a physical

marciobaesse — Thu, 21 Jun 2012 18:27:41 GMT

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/31sg/configuration/guide/vrf.pdf