topic Re: No switchport: command rejected, not allowed on this interfa in Switching

No switchport: command rejected, not allowed on this interface(3560X)

sean chang — Thu, 07 Mar 2019 01:03:11 GMT

I got great help from experts here, so I just keep asking for help on our new catalyst 3560X switch(12.2(58)SE1).

Purpose: Intervlan routing,

actions taken: I created Vlan10 with 10.10.1.1/24; vlan20 with 10.20.1.1/24 on this new switch, IP routing enabled, Vlan 1 is 10.1.10.2/24 for management

Problem: on a new port ( unconfigured 😞

>interface GigabitEthernet0/24

>no switchport

command rejected, not allowed on this interface

I have googled a while but couldn't firgured out why this command is rejected, what should I prepare the port before I can run "no switchport"?

Any suggestions and advises are greatly appreciated.

Re: No switchport: command rejected, not allowed on this interfa

Thotsaphon Lueangwattanaphong — Fri, 13 May 2011 19:33:27 GMT

Hi,

Please post "show version" , "show license detail" and "show run interface g0/24".

HTH,

Toshi

Re: No switchport: command rejected, not allowed on this interfa

sean chang — Fri, 13 May 2011 19:42:45 GMT

thanks, Toshi,

so now I think it's a license problem? becuase I upgraded the IOS, it's now lanbase (before it's IPbase).........

>show ver

License Level: lanbase
License Type: Default. No valid license found.
Next reload license Level: lanbase

cisco WS-C3560X-24 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1420P11G
Last reset from power-on
3 Virtual Ethernet interfaces
1 FastEthernet interface
28 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 58:8D:09:97:6C:80
Motherboard assembly number     : 73-12554-04
Motherboard serial number       : FDO14400EPJ
Model revision number           : A0
Motherboard revision number     : A0
Model number                    : WS-C3560X-24T-S
Daughterboard assembly number   : 800-32786-01
Daughterboard serial number     : FDO14390K7N
System serial number            : FDO1420P11G
Top Assembly Part Number        : 800-31331-01
Top Assembly Revision Number    : A0
Version ID                      : V01
CLEI Code Number                : COMJU00ARA
Hardware Board Revision Number : 0x02

Switch Ports Model              SW Version            SW Image
------ ----- -----              ----------            ----------
*    1 30    WS-C3560X-24       12.2(58)SE1           C3560E-IPBASEK9-M

Re: No switchport: command rejected, not allowed on this interfa

Thotsaphon Lueangwattanaphong — Fri, 13 May 2011 21:17:24 GMT

Hi,

You got it.

########

Routed Ports

A routed port is a physical port that acts like a port on a router; it does not have to be connected to a router. A routed port is not associated with a particular VLAN, as is an access port. A routed port behaves like a regular router interface, except that it does not support VLAN subinterfaces. Routed ports can be configured with a Layer 3 routing protocol. A routed port is a Layer 3 interface only and does not support Layer 2 protocols, such as DTP and STP.

Note : Routed ports are not supported on switches running the LAN base feature set.

########

Many Thanks

Toshi

Re: No switchport: command rejected, not allowed on this interfa

Dario Francesco Vanin — Tue, 30 Apr 2013 03:12:43 GMT

Hi guys,

I have the same problem. What license is needed to use the "routed ports" function on my

WS-C3560X-48?

Do you also know roughy the cost?

I expected this function to be included when I bought a Layer3 swich.

Thanks,

Dario

Re: No switchport: command rejected, not allowed on this interfa

Bilal Nawaz — Tue, 30 Apr 2013 05:05:54 GMT

Hello Dario, you will need an ip base license at minimum I think. You should have had the option to purchase the switch with the license. If no license was requested they just ship out a basic LAN license with the switch. Please contact your reseller for a quote on a suitable license for you, I'm not entirely sure what they cost.
They should also be able to advise you on which license you need for any requirements you may have.

Hope this helps

Sent from Cisco Technical Support iPhone App

No switchport: command rejected, not allowed on this interface(3

Dario Francesco Vanin — Tue, 30 Apr 2013 05:29:27 GMT

Hi Bilal,

Here below my version. What is the code of the upgrade to buy? I need to route 5 VLANS.

From the output of the command, it looks like my license is lanbase but my image is IPBASE.

Thanks,

Dario

Cisco IOS Software, C3560E Software (C3560E-IPBASEK9-M), Version 15.0(1)SE2, REL EASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Compiled Thu 22-Dec-11 00:15 by prod_rel_team

ROM: Bootstrap program is C3560E boot loader

BOOTLDR: C3560E Boot Loader (C3560X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTW ARE (fc1)

SWCORE01 uptime is 3 weeks, 4 days, 4 hours, 48 minutes

System returned to ROM by power-on

System restarted at 08:39:26 AWST Fri Apr 5 2013

System image file is "flash:c3560e-ipbasek9-mz.150-1.SE2.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

License Level: lanbase

License Type: Permanent

Next reload license Level: lanbase

cisco WS-C3560X-48 (PowerPC405) processor (revision A0) with 262144K bytes of memory.

Switch Ports Model SW Version SW Image

------ ----- ----- ---------- ----------

* 1 54 WS-C3560X-48 15.0(1)SE2 C3560E-IPBASEK9-M

Re: No switchport: command rejected, not allowed on this interfa

Bilal Nawaz — Tue, 30 Apr 2013 05:34:43 GMT

Hello Dario, the output shows you are on a LAN base feature set even though you have software supporting ip base.

License Level: lanbase
License Type: Permanent
Next reload license Level: lanbase

Can you do a 'show license udi' please?

You will just need the ip base licence to accomplish what you want to do.

Sent from Cisco Technical Support iPhone App

No switchport: command rejected, not allowed on this interface(3

Dario Francesco Vanin — Tue, 30 Apr 2013 05:42:14 GMT

Here the output of the command:

show license udi

Device# PID SN UDI

-----------------------------------------------------------------------------

*0 WS-C3560X-48T-L FDO1605K35A WS-C3560X-48T-L:FDO1605K35A

Do you mean that I have to buy a license called "ip base" and it does not require any IOS upgrade?

Thanks,

Dario

Re: No switchport: command rejected, not allowed on this interfa

Bilal Nawaz — Tue, 30 Apr 2013 05:47:34 GMT

Yes Dario, correct

Please see here: http://www.cisco.com/en/US/products/ps10744/prod_models_comparison.html

The IP Services feature set is available as an upgrade option at the time of ordering or through a license at a later time.

Hope this helps

Sent from Cisco Technical Support iPhone App

No switchport: command rejected, not allowed on this interface(3

Dario Francesco Vanin — Tue, 30 Apr 2013 06:14:14 GMT

Thanks Bilal for your support.

No switchport: command rejected, not allowed on this interface(3

Thotsaphon Lueangwattanaphong — Tue, 30 Apr 2013 06:21:43 GMT

Good Job! Bill

5-Point

Toshi

CCIE

Re: No switchport: command rejected, not allowed on this interfa

Bilal Nawaz — Tue, 30 Apr 2013 06:36:54 GMT

You're welcome Dario, any time 🙂

Thanks Toshi! Hope this can help others too.

Sent from Cisco Technical Support iPhone App

Re: No switchport: command rejected, not allowed on this interfa

fhk — Tue, 22 Nov 2022 05:43:26 GMT

ESW3#show version
*Mar 1 00:02:07.607: %SYS-5-CONFIG_I: Configured from console by console
ESW3#show version
Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 17-Aug-10 12:08 by prod_rel_team

ROM: ROMMON Emulation Microcode
ROM: 3700 Software (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)

ESW3 uptime is 2 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
--More--

Re: No switchport: command rejected, not allowed on this interfa

sarjayservino — Wed, 15 Feb 2023 11:31:20 GMT

Same to my problem. There is other way for this? Iwant to put ip inside my interface

Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.2(4)E6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Thu 05-Apr-18 02:22 by prod_rel_team

ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(58r)SE1, RELEASE SOFTWARE (fc1)

CoreSwitch2 uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:c3750e-universalk9-mz.152-4.E6.bin"
Last reload reason: Reload command

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

License Level: lanbase
License Type: Permanent
Next reload license Level: lanbase

cisco WS-C3750X-48P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1808Z1YU
Last reset from power-on
21 Virtual Ethernet interfaces
1 FastEthernet interface
52 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 74:26:AC:C5:79:00
Motherboard assembly number     : 73-12553-11
Motherboard serial number       : FDO180902AD
Model revision number           : A0
Motherboard revision number     : A0
Model number                    : WS-C3750X-48PF-L
Daughterboard assembly number   : 800-32727-03
Daughterboard serial number     : FDO18081KQX
System serial number            : FDO1808Z1YU
Top Assembly Part Number        : 800-31324-09
Top Assembly Revision Number    : B0
Version ID                      : V06
CLEI Code Number                : CMMPS00DRA
Hardware Board Revision Number : 0x05

Switch Ports Model                     SW Version            SW Image
------ ----- -----                     ----------            ----------
*    2 54    WS-C3750X-48P             15.2(4)E6             C3750E-UNIVERSALK9-M

Configuration register is 0x

Re: No switchport: command rejected, not allowed on this interfa

sarjayservino — Wed, 15 Feb 2023 14:06:16 GMT

The only solution for this, is to buy ah license or use svi for assigning ip address on the interface?