topic Re: Virtual switch 6509 in Switching

Virtual switch 6509

funyphong — Wed, 06 Mar 2019 09:18:27 GMT

When I converted my switchs(6509E) to virtual mode , my service modules were powered down, I tried to use command " power enable " but not active. Pls tell me how turn on

Regards

Re: Virtual switch 6509

dipjitsengupta — Thu, 11 Sep 2008 04:39:25 GMT

hi,

pls tell me which IOS u have in that 6509E switch???

Re: Virtual switch 6509

funyphong — Thu, 11 Sep 2008 04:59:03 GMT

CORE1#show version

Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-VM), Versi on 12.2(33)SXH1, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Compiled Thu 17-Jan-08 08:09 by prod_rel_team

Re: Virtual switch 6509

abeid — Thu, 11 Sep 2008 06:24:58 GMT

Hi, the 12.2(33)-SXH1 version doesnt support any service modules apart from NAM-1,2. It is in the pipeline to support more service modules in future release 12.2-SXI.

Re: Virtual switch 6509

Calin C. — Thu, 11 Sep 2008 06:33:45 GMT

Hi!

You are using a VSS there? Do a show module and paste here the results.

In case you are using VSS,

do the following:

sh platform hardware pfc mode

PFC operating mode : (tell us what is displayed here)

If modules are installed in a system that contains a DFC3C, then the module may never be allowed to power up.

Cheers,

Calin

Re: Virtual switch 6509

funyphong — Thu, 11 Sep 2008 07:14:55 GMT

CORE1#show module

Mod Ports Card Type

Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1213KKAY

2 6 Firewall Module WS-SVC-FWM-1 SAD121204LJ

3 1 Application Control Engine Module ACE20-MOD-K9 SAD1212020S

4 8 Intrusion Detection System WS-SVC-IDSM-2 SAD120907H9

5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1213K85Z

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 001f.9e3d.d800 to 001f.9e3d.d82f 2.7 12.2(14r)S5 12.2(33)SXH1 Ok

2 001f.6c89.112a to 001f.6c89.1131 4.2 Unknown Unknown PwrDown

3 001f.9e1a.e9b8 to 001f.9e1a.e9bf 2.3 Unknown Unknown PwrDown

4 001f.9e1a.c238 to 001f.9e1a.c23f 6.3 Unknown Unknown PwrDown

5 001e.7a58.5f40 to 001e.7a58.5f47 2.0 8.5(2) 12.2(33)SXH1 Ok

CORE1#show platform hardware pfc mode

PFC operating mode : PFC3C

Configured PFC operating mode : None

Re: Virtual switch 6509

funyphong — Thu, 11 Sep 2008 07:26:53 GMT

CORE1#show module

Mod Ports Card Type

Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1213KKAY

2 6 Firewall Module WS-SVC-FWM-1 SAD121204LJ

3 1 Application Control Engine Module ACE20-MOD-K9 SAD1212020S

4 8 Intrusion Detection System WS-SVC-IDSM-2 SAD120907H9

5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1213K85Z

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 001f.9e3d.d800 to 001f.9e3d.d82f 2.7 12.2(14r)S5 12.2(33)SXH1 Ok

2 001f.6c89.112a to 001f.6c89.1131 4.2 Unknown Unknown PwrDown

3 001f.9e1a.e9b8 to 001f.9e1a.e9bf 2.3 Unknown Unknown PwrDown

4 001f.9e1a.c238 to 001f.9e1a.c23f 6.3 Unknown Unknown PwrDown

5 001e.7a58.5f40 to 001e.7a58.5f47 2.0 8.5(2) 12.2(33)SXH1 Ok

CORE1#show platform hardware pfc mode

PFC operating mode : PFC3C

Configured PFC operating mode : None

Re: Virtual switch 6509

plgingembre — Sat, 13 Sep 2008 21:20:35 GMT

Hi,

Here is what you were asking :

rtr-sem-dc#sh platform hardware pfc mode

PFC operating mode : PFC3C

Configured PFC operating mode : None

rtr-sem-dc#

Kind Regards,

Pierre-Louis

Re: Virtual switch 6509

Ryan Carretta — Sun, 14 Sep 2008 07:20:37 GMT

Hi,

Your question was already answered in this thread:

The service modules you have aren't supported with VSS quite yet. VSS support for ACE10, ACE20, FWSM, IDSM, and WiSM will come with the 12.2(33)SXI code release.

-Ryan

Re: Virtual switch 6509

ajagadee — Fri, 14 Nov 2008 16:35:48 GMT

Hi,

FYI.. 12.2(33)SXI for the Catalyst 6500 has been posted on cisco.com and this version of software does support FWSM with VSS.

Release Notes for the Catalyst 6500 Series and Cisco 7600 Series Firewall Services Module, 4.0(x)

http://www.cisco.com/en/US/docs/security/fwsm/fwsm40/release/notes/fwsmrn40.html

Regards,

Arul

*Pls rate if it helps*