topic Re: Access Meraki switch locally without cloud question in Cloud Networking Platform

Access Meraki switch locally without cloud question

keithli — Thu, 06 Oct 2022 04:25:49 GMT

Dear All,

Would like to know can i access meraki switch locally via ssh, console, or internal web portal without cloud base ? Thanks

Keith

Re: Access Meraki switch locally without cloud question

ww^ — Thu, 06 Oct 2022 06:30:35 GMT

You can access a local web page, but its just for basic setting / first time setup to the cloud.

https://documentation.meraki.com/General_Administration/Tools_and_Troubleshooting/Using_the_Cisco_Meraki_Device_Local_Status_Page#MS_Series

Re: Access Meraki switch locally without cloud question

keithli — Thu, 06 Oct 2022 06:54:26 GMT

so for example if my meraki switch ip is 192.168.24.2, i could access via web broswer with this IP ? The username will be the serial number and empty in password ?

Re: Access Meraki switch locally without cloud question

BlakeRichardson — Thu, 06 Oct 2022 08:04:34 GMT

Correct. Bear in mind the switch still needs to be able to communicate with the Meraki dashboard for it to work, you cannot you any Meraki equipment without it being licensed and communicating with the dashboard.

Re: Access Meraki switch locally without cloud question

keithli — Thu, 06 Oct 2022 08:09:00 GMT

how about if the meraki switch has already licensed in the dashboard, and in any case that inernet broken down, the AP and meraki switch wont be able to work am i correct ?

Re: Access Meraki switch locally without cloud question

aleabrahao — Thu, 06 Oct 2022 12:46:46 GMT

The Meraki Cloud is an out of band architecture, meaning that no client data flows through the Cloud. The system is also designed to handle connectivity failures gracefully.

If a Meraki data center experiences an outage, your network will automatically fail over to another Meraki data center. During the fail-over time your network will experience connectivity loss as described above.

Assuming you have setup email alerts, you will receive an email when a Meraki node loses connectivity to the Cloud, allowing you to take corrective action if necessary.

For more information on local device management, see Using the Cisco Meraki Device Local Status Page.

Overview
Safe Configuration
Safe configuration means that “the device has connectivity to cloud and hasn't rebooted for 30 minutes following a configuration change.” That is, the safe configuration is the last configuration the device received from the cloud that was not followed by a reboot within 30 minutes.

https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Behavior_during_Connection_Loss_to_Cisco_Meraki_Cloud

Re: Access Meraki switch locally without cloud question

joey.debra — Thu, 06 Oct 2022 19:56:16 GMT

About the username password thing, it is correct when the switch has been reset or not configured.

So indeed the username is it's serial number exactly as it is written in caps and with dashes and the password is empty.

However if a switch was part of an existing network there could have been a user admin with some configured password.

Switches continue to forward and use their typical L2 and L3 protocols if they lose connectivity to the cloud.

The local configuration is limited to setting a management IP address and VLAN, and changing the native VLAN or ports.

Re: Access Meraki switch locally without cloud question

keithli — Fri, 07 Oct 2022 02:14:20 GMT

does it means if internet broken down, the meraki switch are still workable for L2 and L3 ? users are still able to connect the Meraki AP for internal access ?

Re: Access Meraki switch locally without cloud question

aleabrahao — Fri, 07 Oct 2022 09:42:21 GMT

MX and MX I've already tested it in practice and I can guarantee that it will continue to work, but the access points (MR) I'm not 100% sure.

Re: Access Meraki switch locally without cloud question

keithli — Mon, 10 Oct 2022 01:36:45 GMT

noted and one more question, if i first purchase meraki switch without licensed in the dashboard, can it function as L2 ? or it must work once i licensed ?

Re: Access Meraki switch locally without cloud question

aleabrahao — Mon, 10 Oct 2022 10:58:45 GMT

You need to purchase a license.