topic Noise issue from WebEx room kit Pro in Webex Devices

Noise issue from WebEx room kit Pro

declanrafferty1 — Thu, 21 Jan 2021 14:11:40 GMT

Hi all, I am using a Webex room kit Pro and it is connected to a Tesira Forte. The Tesira is picking noise from the codec even when i am not in a call, this noise cannot be heard when recording a call be when i play the recording back i can hear this noise. Is there a setting on the codec to stop this?

Re: Noise issue from WebEx room kit Pro

Sebastian Leuser — Tue, 02 Feb 2021 14:26:54 GMT

Does the Tesira require power from the codec? If not you should disable the phantom power from the inputs.

Audio Input Microphone [1..8] PhantomPower
Define whether or not to have phantom power (48 V +/- 1 V) on the microphone input.
Requires user role: ADMIN, INTEGRATOR
Default value: On
Value space: Off/On
Off: Disable the phantom power on the microphone input. Use this when connecting to
equipment that do not need phantom power, such as external mixers.
On: Enable the phantom power on the microphone input. Use this when connecting
directly to microphones that require phantom power, including the Cisco Table
Microphone and Cisco Ceiling Microphone.

Re: Noise issue from WebEx room kit Pro

declanrafferty1 — Wed, 03 Feb 2021 17:43:50 GMT

Thanks Sabastian..

Re: Noise issue from WebEx room kit Pro

henrykyburg — Thu, 08 Feb 2024 17:24:58 GMT

We have dozens of WebEx Roomkit Pro units. They all output bad audio out analog output 1. In a call or not. All Proximity and Ultrasound and phantom power off. All sources muted in the Audio Console. The issue is a high frequency distorted static noise. All of our units are doing this. I have recordings to demonstrate. The level of the noise is low enough that most people might not complain, but as a professional I know it's causing fatigue in our learners at University of California.

Re: Noise issue from WebEx room kit Pro

Montypython — Sun, 11 Feb 2024 11:55:00 GMT

Hi did you get a solution for this as we are having the same issue on the WebEx SX80's connected to a Tesira only started on Friday did Cisco update anything as the Proximity Pairing Ultrasound Max Volume is set to zero which used to be off.

This high pitch whining can only be heard on the recording, not during the live session?

Any help greatly appreciated.

Re: Noise issue from WebEx room kit Pro

Wayne DeNardi — Wed, 14 Feb 2024 03:41:39 GMT

You should be able to turn Proximity Off completely via the web interface rather than just setting the max volume to zero.

It would probably also pay to add a low-pass filter to your Tesira for the input that the codec's output is connected to, to drop the ultrasound frequencies that Proximity uses so they don't end up at your recording solution.

Re: Noise issue from WebEx room kit Pro

declanrafferty1 — Wed, 14 Feb 2024 21:47:09 GMT

Thanks Wayne

Re: Noise issue from WebEx room kit Pro

henrykyburg — Thu, 15 Feb 2024 15:33:41 GMT

Cisco sent me instructions (below) but the issue remains.

---

Let’s try the following for ultrasound:

Please go to the endpoints UI and go to: Standby > WakeUpOnMotionDetection

Please check if that’s off, if not, please turn it off, and reduce the ultrasound “Max volume” to 0

Don’t forget to click “Save” so we can have that configuration applied.

If the ultrasound keeps activating, please use the following command:

*c xConfiguration RoomAnalytics PeoplePresence Input Ultrasound: Off

Re: Noise issue from WebEx room kit Pro

fletcher.j — Thu, 18 Jul 2024 18:22:31 GMT

We have just installed three new Pro devices in a some of our classrooms. I've never run into this with our other units, but on all of these the output (Output 1) sound like a Model T running down the road with an industrial strength bubble maker strapped to it. Ours also are going into a Tesira device. You can only hear it on our recordings, but it is causing all types of hate and discontent in the ranks.

Re: Noise issue from WebEx room kit Pro

fletcher.j — Thu, 18 Jul 2024 18:27:29 GMT

Ultrasound got it!

Re: Noise issue from WebEx room kit Pro

fletcher.j — Thu, 18 Jul 2024 18:28:09 GMT

Ultrasound MaxVolume took care of ours! Thanks.