topic Jabber not indicating when "on a call" in Collaboration Applications

Jabber not indicating when "on a call"

markpexa1 — Sun, 17 Mar 2019 21:44:27 GMT

Starting sometime last week a handful of users Presence status isn't displaying that they are on a call (mine included). No significant configuration changes were made to Presence or CallManager. I am part of Standard CTI Enabled group and Standard CTI Allow Control of Phones supporting Rollover Mode. Presence indicates desk phone control enabled. My phone is listed as a controlled device under my CallManager profile. As I said before, this was working.... Any suggestions on where to look further?

Jabber Client 9.0.3

CallManager 8.6.2

Unified Presence 8.5.3

Jabber not indicating when "on a call"

Aaron Harrison — Tue, 30 Oct 2012 18:26:57 GMT

That status is managed by the link between DNs and users (i.e. the list of associated users at the bottom of the line appearance configuration page) . Check that still lists you on your line appearance.

Otherwise the SIP trunk between CUPS and CUCM might need looking at.

Regards

Aaron

Jabber not indicating when "on a call"

markpexa1 — Tue, 30 Oct 2012 18:56:35 GMT

Thanks for the reply Aaron. Yes, my user is still associated with my DN.

Jabber not indicating when "on a call"

markpexa1 — Wed, 31 Oct 2012 15:26:57 GMT

Using the following document, I checked the SIP trunk configurations.

http://www.cisco.com/en/US/products/ps6837/products_configuration_example09186a0080bb251f.shtml#sip-cucm

All settings checked out.

Jabber not indicating when "on a call"

David Levinson — Wed, 31 Oct 2012 16:35:59 GMT

Having the same issue. Deleted the CSF device completely and re-built. Still didn't fix it. Re-associated with end user.

Jabber not indicating when "on a call"

Richard Hermann — Wed, 31 Oct 2012 21:39:35 GMT

Is this an issue of seeing others presence? I mean, on your client, does it say you're on the phone, but not to anyone else?

What comes to mind is if you have two+ presence nodes in a cluster, some users maybe associated to one node, while some on the other(s). If the nodes are not in the same multicast domain, they won't pass presence info to one another. To fix that, change the 'Routing Communication Type' to Router-to-Router under cluster topology settings on your CUP server.

Jabber not indicating when "on a call"

David Levinson — Thu, 01 Nov 2012 03:39:06 GMT

No, even on the local client it just always stays "Available." The majority of other users are fine, at least for me this is only happening to a handful. And I do have Router-to-Router set. Thanks for the ideas, anything helps at this point

Jabber not indicating when "on a call"

Christos Georgiadis — Thu, 01 Nov 2012 22:30:13 GMT

I suspect a configuration issue in callmanager.

Since you have working users I suggest you compare the following

-- Line configuration of a working phone and a non working phone (user association)

-- End user configuration by comparing a working and a non working user (especially the device / device profile association, primary extension fields and end user groups)

HTH,

Christos

Jabber not indicating when "on a call"

markpexa1 — Tue, 06 Nov 2012 14:57:26 GMT

Mine says available on the local client as well. The nodes are in the same multicast domain. Checked and re-checked line configuration and end user configuration. Restarted both nodes last night. We are planning on updating to 8.6.4 on Thursday. Thanks for all of the input.

Jabber not indicating when "on a call"

Muhammad Maqsood Mushtaq — Tue, 06 Nov 2012 15:35:16 GMT

Hi Mark,

Please review this post and "Off Hook Dialing Does Not Change Presence States" section in "Admin Guide - Troubleshoot Cisco Jabber for Windows" for some configuration checks.

Thanks,

Maqsood

Jabber not indicating when "on a call"

markpexa1 — Fri, 07 Dec 2012 16:26:05 GMT

The issue ended up being the SIP Trunk between CallManager and Presence. The trunk on CallManager had a subscribe calling search space set to none.