topic Cisco Jabber for Windows can place Point to Point Video Call but can't place Multiparty Video Call in Collaboration Applications

Cisco Jabber for Windows can place Point to Point Video Call but can't place Multiparty Video Call

Shashank Gavankar — Sun, 17 Mar 2019 21:32:03 GMT

Hi,

I have CUCM 8.6.2.21900-5 and Presence 8.6.4 and I have install Cisco Jabber for Windows ( CiscoJabber-Install-ffr.9-0-1.zip ) in 4 PCs .

We can place Point to Point Video Call but can't place Multiparty Video Call,

When we add 3rd party in Point to Point Video Call that time conference call automatically converts into Audio Call only.

Regards,

Shashank

Cisco Jabber for Windows can place Point to Point Video Call but

Michael Boscia — Thu, 09 Aug 2012 23:14:03 GMT

Do you have a video MCU or an ISR G2 with PVDMv3 DSPs with video conferencing resources defined in your MRG and MRGL that are assigned to the device pool that your Jabber devices are assigned to?

Cisco Jabber for Windows can place Point to Point Video Call but

Shashank Gavankar — Mon, 13 Aug 2012 04:47:14 GMT

We dont have any external video MCU or an ISR G2 with PVDMv3.

Is it required for multiparty video call ?

Can we configure CUCM to do multiparty video without MCU or ISR ?

Re: Cisco Jabber for Windows can place Point to Point Video Call

Michael Boscia — Mon, 13 Aug 2012 10:09:27 GMT

Without an ISR or an MCU or some sort of a bridging service, the answer is no.

Sent from Cisco Technical Support iPhone App

Cisco Jabber for Windows can place Point to Point Video Call but

plafond12 — Fri, 17 Aug 2012 18:08:21 GMT

Hi Michael,

I do have an ISR G2 router with pvdm3 configured as homogeneous.

I verified that the DSPs are being used when

I try to do the video conferencing, however

I cannot videoconference 3 devices.

Please note the the videoconference works

With my 9971 phones.

I'm using codec h264 cif-30-740.

Do you suspect a codec issue for jabber?

Re: Cisco Jabber for Windows can place Point to Point Video Call

Steven DiStefano — Fri, 05 Oct 2012 13:02:48 GMT

What is the current official position on this?

I am interested in positioning Jabber for Windows Clients forming Video teleconferences using only PVDM3s on ISR-G2's.

From what I have read, it looks like this is supported.

I also find some inconsistent documentation about 'lecture mode', where one doc says its supported, but the other says its not. Are we limited to only active speaker via CUCM control? What are the rules on content sharing inside a video conference?

Cisco Jabber for Windows can place Point to Point Video Call but

danielgarzon — Wed, 28 Nov 2012 10:54:10 GMT

Hi,

Are there any config example?

I have a MCU and I want to integrate Jabber and MCU for Multiparty Video Call.

Thanks

Re: Cisco Jabber for Windows can place Point to Point Video Call

Matt McAuley — Thu, 29 Nov 2012 22:41:21 GMT

No BFCP screen sharing support for PVDM3.
Active speaker presentation.

Add the resource the UCM just like an Xcode or conf bridge.

Sent from Cisco Technical Support iPhone App

Cisco Jabber for Windows can place Point to Point Video Call but

plafond12 — Fri, 19 Apr 2013 14:54:54 GMT

I even created a separate profile for 720p video which jabber uses as shown below, but still no go.

Has anyone been able to get Jabber for windows video conference working?

dspfarm profile 2 conference video homogeneous

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec g729r8

codec g729br8

codec h264 720p frame-rate 30 bitrate 2mbps

maximum conference-participants 8

maximum sessions 4

associate application SCCP

Cisco Jabber for Windows can place Point to Point Video Call but

Paul McGurn — Sat, 04 May 2013 03:31:59 GMT

Were you able to figure this out? I've yet to find any documentation officially noting support for Jabber on the PVDM3's, but it "sounds" like it should work OK via MRGL.

Cisco Jabber for Windows can place Point to Point Video Call but

Ravipati Seetaramaiah — Mon, 02 Sep 2013 15:40:12 GMT

I have the same problem for making multi party video call using CUCM 7.1.5, Meeting Place 8.6 as conference bridge and cisco Jabber 9.2.3.

Point to point video is ok but when the third party is added it becomes a audio call. Any suggestions Please??

Thank you.

Am experiencing the same

Ismail Egieya — Mon, 30 Jun 2014 14:49:46 GMT

Am experiencing the same issue; I can make point-to-point video calls on Jabber but having issues making video conference calls even after I configured video conference bridge via an ISR router and also have an MCU set-up as well.

Any ideas on what to check next?

Hi, Just wondering if you

Ismail Egieya — Mon, 30 Jun 2014 14:50:30 GMT

Hi,

Just wondering if you managed to fix this problem?