topic Re: CUCM 11.5 Integration with Microsoft Teams in Collaboration Applications

CUCM 11.5 Integration with Microsoft Teams

FMKazi3467351 — Wed, 20 Oct 2021 06:16:11 GMT

Hello All,

I need to know what are the Pre requisites for CUCM to be able to Integrate with MS Teams.

For starters, I have CUCM 11.5, will I be able to Integrate with MS Teams, if yes, then will it be fully operational or with limitations.

Thanking you all in advance for your kind suggestions.

Re: CUCM 11.5 Integration with Microsoft Teams

Roger Kallberg — Wed, 20 Oct 2021 07:07:46 GMT

Have a look at these two documents that outline what is needed.

Direct Routing for Microsoft Phone System with Cisco Unified Communications Manager (UCM) via Cisco Unified Border Element (CUBE)

Direct Routing for Microsoft Phone System with Cisco Unified Border Element (CUBE)

The second one is for an integration for PSTN with Verizon, but in general is applicable to the integration with CM as well and is actually referenced in the first document as for the details for how to configure the SBC for the integration.

This configuration is absolutely not for the fainthearted as it is pretty complex, but with a little reading and studying it's for sure doable.

Re: CUCM 11.5 Integration with Microsoft Teams

FMKazi3467351 — Wed, 20 Oct 2021 07:50:09 GMT

@Roger Kallberg Thanks for your instant response but in the documentation it still specifies the CUCM as 12.5 or any supported version. So I am still stuck at my query which version is compatible with Microsoft Teams. So it would be very kind of you if you could provide me with the necessary information.

Re: CUCM 11.5 Integration with Microsoft Teams

Roger Kallberg — Wed, 20 Oct 2021 09:29:18 GMT

The documents mention the version that was used for the tests, but it also states that any supported version of CM could be used.

AFAIK With supported version what is referenced here would be any current version that is supported by Cisco, ie not announced as EOL and has reached EOS.

Re: CUCM 11.5 Integration with Microsoft Teams

Steven L — Wed, 20 Oct 2021 12:23:50 GMT

11.5 will work fine. I have done this integration a few times. The critical version requirements are on the SBC (CUBE if you are using Cisco) side.

There are many nuances associated with this.

"Fully Operational" is a bit vague in this context. What is your vision of fully operational?

Re: CUCM 11.5 Integration with Microsoft Teams

fernando vila — Thu, 27 Jan 2022 16:46:31 GMT

Hi Roger can I use more than a ISR CUBE to get redundancy? I know the HA functionality of ISR CUBE but I´ll good like to have a redundancy in two o more different countries. For this case the ISR CUBE HA is not supported.

Thanks

Re: CUCM 11.5 Integration with Microsoft Teams

Roger Kallberg — Thu, 27 Jan 2022 17:57:33 GMT

Sure. It is normal call routing in CM, so utilise that to distribute outbound calls across the gateways. Inbound is another story as that would involve configuration for call routing on the Microsoft platform and that’s well outside of my area.

Re: CUCM 11.5 Integration with Microsoft Teams

fernando vila — Thu, 27 Jan 2022 21:15:36 GMT

Yes, of corse, the CUCM has TEJO configured for outbound calls. The question is about the ISR CUBE that join the MS Teams world with the Cisco world. I found several examples but just they use the ISR CUBE HA feature. The CUBE HA is not supported for devices placed on different countries. This is explain on page 56 of following guide.

https://www.cisco.com/c/dam/en/us/solutions/collateral/enterprise/interoperability-portal/direct-routing-with-cube.pdf

Re: CUCM 11.5 Integration with Microsoft Teams

Roger Kallberg — Fri, 28 Jan 2022 06:30:19 GMT

The little I do know about the MS side is that you can create multiple gateways in your MS tenant and setup call routing logic in it.

Not sure what TEJO is? What I meant by normal call routing in CM is that you can have multiple trunks put into your RG/RL construct to pass calls via multiple SBCs.

Re: CUCM 11.5 Integration with Microsoft Teams

Scott Leport — Fri, 28 Jan 2022 19:44:55 GMT

Hi,

If I have understood you correctly, are you asking if it’s possible to have 2x SBC’s in different networks and achieve redundancy in the Microsoft tenant? Answer is yes and you can set up call routing logic for outbound calls from Teams to CUBE, similar to what you do in CUCM via Route Groups & Route Lists.

I have worked on a couple of these deployments where the SBC’s have been in different DC’s. It’s not box-to-box redundancy as explained in the doc, but there is redundancy built in that most of the standard configuration is the same (different IP’s obviously) and the same numbers delivered to either SBC and either SBC can process inbound & outbound calls.