topic ACS 5.4 experiences? in Network Access Control

ACS 5.4 experiences?

Ben.Levin — Mon, 11 Mar 2019 03:08:05 GMT

I'm planning to upgrade from ACS 5.3 to 5.4 in a couple of weeks in order to take advantage of the IPv6 support. Is there anyone running 5.4 that can provide any info on 5.4 experiences/issues/caveats, etc? Thanks!

ACS 5.4 experiences?

jrabinow — Thu, 28 Feb 2013 14:32:12 GMT

There are a couple of points that should be taken into consideration before upgrading:

(taken from release notes)

If you have either ACS 5.2 or ACS 5.3 installed on your machine, you can upgrade to ACS 5.4 using one of the following two methods:

•Upgrading an ACS Server using the Application Upgrade Bundle

•Reimaging and Upgrading an ACS Server

You can only perform an application upgrade bundle, on either a Cisco appliance or a virtual machine, if the disk size is greater than or equal to 500 GB. If you have a smaller disk size, you need to reimage to ACS 5.4 followed by a restore of the backup taken in ACS 5.2 or ACS 5.3 version to trigger the upgrade.

When you upgrade from ACS 5.3 to 5.4, it is mandatory to install ACS 5.3.0.40.8 prior to the upgrade or the upgrade may fail. If you use the version prior to ACS 5.3.0.40.6, then you might hit an error and the upgrade will not proceed. Note that ACS 5.4 does not include all fixes that are included in 5.3.0.40.8. Therefore, if any of these fixes in 5.3.0.40.8 are required in your deployment, then you should install patch 5.4.0.46.1 after you upgrade to ACS 5.4.

Will be interested to hear feedback on the TACACS+ IPv6 support

ACS 5.4 experiences?

ds6123 — Mon, 29 Apr 2013 16:47:00 GMT

Same question here. Is anyone having any major issues with 5.4 (besides what's in the release notes)? Starting from scratch, should I load 5.3 and install the latest patch? Or go to 5.4 with the latest patch?

ACS 5.4 experiences?

Jatin Katyal — Mon, 29 Apr 2013 17:10:17 GMT

No, no major issues have been reported yet.

Jatin Katyal

- Do rate helpful posts -

ACS 5.4 experiences?

Ben.Levin — Mon, 29 Apr 2013 17:40:15 GMT

I successfully upgraded my 4 appliances from ACS 5.3 to 5.4 in March. It was pretty straightward except that you have to shift the log collector around and detach each appliance from the cluster before you upgrade it. This was a little confusing but essentially you detach the first instance, upgrade it, and then it becomes the primary for the subsequently upgraded instances. Once you finish the upgrade you can set any of the instances as the primary and also set the log collector.

ACS 5.4 experiences?

jrabinow — Tue, 30 Apr 2013 09:52:28 GMT

Some highlights for patches available for ACS 5.4

- Patch 1 provides support for later browser versions; particualrly for firefox (details in release notes)

- Patch 2 provides support for Windows 2012

ACS 5.4 experiences?

ds6123 — Sat, 04 May 2013 17:35:35 GMT

Thanks everyone! 5.4 with the latest patches applied seems to work.

ACS 5.4 experiences?

minkumar — Mon, 06 May 2013 22:33:38 GMT

Hi Ben,

To further add to the above posts, Here is the release notes that you can refer for ACS 5.4:

http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.4/release/notes/acs_54_rn.html

Regards

Minakshi (Do rate the helpful posts )