topic Cisco ise on vm Failed to start database in Network Access Control

Cisco ise on vm Failed to start database

Giuliano Gerardi — Mon, 11 Mar 2019 02:33:13 GMT

vmware 4.1 (or maybe 4.0.1)

configured with 2 core minimum freq 3.6Ghz

200Gb HD on single physical drive (minimum requirement),

no thin provisioning

datastore vmfs 3, 2Mb block size,

ethernet : flexible network adapter

ram 4Gb

Scsi controller

setup......

bum

.....

....

ISE Database listener not ready yet. Seconds left before timeout: 0

error:[cpminitialsetup.sh]

##########################################################################

ERROR: FAILED TO START DB!

Database is not available within timeout of 240 seconds.

This could be the result of incorrect network interface configuration,

or lack of resources on the appliance or VM. Please fix the issue and

run the following CLI to re-prime database:

'application reset-config ise'

error:[cpminitialsetup.sh]

##########################################################################

Any advice?

Cisco ise on vm Failed to start database

Tarik Admani — Fri, 14 Sep 2012 14:58:18 GMT

Hi,

Is DNS and configured for forward and reverse records for the hostname you configured before this step?

Also is NTP available to this server?

Thanks,

Tarik Admani
*Please rate helpful posts*

Re: Cisco ise on vm Failed to start database

Giuliano Gerardi — Fri, 14 Sep 2012 15:21:18 GMT

yes it is

for ntp it is local as is synced with vmware

however ntp server has not been elected even tough udp 123 port is open

please note that on the same network a physical 3395 appliance has been setup normally

Re: Cisco ise on vm Failed to start database

Tarik Admani — Fri, 14 Sep 2012 15:27:35 GMT

Are you using RHEL 5 32 bit as the guest operating system in the vmware settings?

Thanks,

Tarik Admani
*Please rate helpful posts*

Re: Cisco ise on vm Failed to start database

Giuliano Gerardi — Fri, 14 Sep 2012 19:53:49 GMT

yes red hat enterprise 5 32 bit

Re: Cisco ise on vm Failed to start database

Tarik Admani — Fri, 14 Sep 2012 20:18:42 GMT

what are you using for ntp clock source? If it is internal can you allow icmp since I noticed this in my current deployment. Once I permitted it, it seemed to sync and work fine.

thanks,

Tarik Admani
*Please rate helpful posts*

Re: Cisco ise on vm Failed to start database

Giuliano Gerardi — Mon, 24 Sep 2012 08:21:07 GMT

that was caused by the virtual machine configured with two disks -.-
someone will get killed soon...

however thank you

Cisco ise on vm Failed to start database

lanny-8080 — Wed, 14 Nov 2012 09:56:38 GMT

Hi Tarik,

I am getting the same error message:

Starting ISE database processes...

##########################################################################

ERROR: FAILED TO START DB!

Database is not available within timeout of 240 seconds.

This could be the result of incorrect network interface configuration,

or lack of resources on the appliance or VM. Please fix the issue and

run the following CLI to re-prime database:

'application reset-config ise'

##########################################################################

This happend when i did command 'application reset-config ise' on a 3395 appliance running 1.1.1.268 code

i appreciate your assistance

Cisco ise on vm Failed to start database

Tarik Admani — Thu, 15 Nov 2012 02:05:42 GMT

Please make sure that the ISE has access to ntp and dns (both forward and reverse records).

Thanks,

Tarik Admani
*Please rate helpful posts*

Re: Cisco ise on vm Failed to start database

Giuliano Gerardi — Thu, 15 Nov 2012 08:24:54 GMT

please make shure the virtual machine respects all the standards defined in the documentation,

pay much attention to the disk size, cluster dimensions and :

1) check the virtual machine is created with only ONE virtual disk

2) check the disk is not splitted on two or more physical disks (the virtual disk must reside on a single physical disk)

in my case the problem was that the virtual machine was created with two 200gb disks and the result was the error mentioned above...

Re: Cisco ise on vm Failed to start database

lanny-8080 — Thu, 15 Nov 2012 09:39:24 GMT

Giuliano,

I am using a 3395 appliance in this case and not a VM.

I will sort and dns and ntp and report back

many thanks

Cisco ise on vm Failed to start database

Colum O'Connor — Wed, 23 Jan 2013 18:10:37 GMT

Hi Lanny

I am running into the same issue on an ISE appliance, 3355. Did you find a solution?

thanks

Colum

Cisco ise on vm Failed to start database

lanny-8080 — Wed, 23 Jan 2013 18:25:14 GMT

Is it a fresh installation?

If it is then you have to ensure that the ntp, dns and domain information is current and active before you proceed with installation otherwise it would most lightly give database error.

steps i took.:

Ensured the ntp, dns ip address, dns domain name was provisioned

re-run the installation

In my case it would take forever for database to initialize and when it does, i still cant connect via web browser but could connect via CLI.

Good luck

Cisco ise on vm Failed to start database

Colum O'Connor — Wed, 23 Jan 2013 20:01:19 GMT

Hi Lanny

It is a fresh install, i am setting it up in the lab to upgrade/patch before bringing it onsite. I provisioned dns, ntp, ip and domain ...I have a 3750 and the default gateway and a router with the ntp address on it and configured as ntp master

Cisco ise on vm Failed to start database

lanny-8080 — Wed, 23 Jan 2013 20:20:21 GMT

dont forget to add the fqdn of the ise terminal to your dns server forward and reverse

let me know what happens

Re: Cisco ise on vm Failed to start database

Naveen Kumar — Fri, 22 Mar 2013 01:33:00 GMT

Please make sure that the ISE has access to ntp and dns (both forward and reverse records).

and as you are using VM machine so 60 to 600 GB of disk storage (size depends on deployment and tasks) are required. But 200 GB or more disk space are required to a production environment.

In your case, I highly recomand you to allot a minimum of 200 GB of disk space and use a hard disk drive with a minimum of 10,000 RPM.

ISE must be installed on a single disk in VMware. If you use several small disks to meet the disk space requirement for installing ISE, you might experience some unexpected behavior.

Cisco ise on vm Failed to start database

s.szklarczyk — Thu, 23 Jan 2014 14:00:29 GMT

I've got same problem. ISO image was broken. Check MD5.

HiI faced this issue today;It

mussabmustafa — Sat, 06 Sep 2014 12:07:52 GMT

I faced this issue today;

It was due to NTP misconfiguration; the server was not syncrounised with NTP server

When I fixed the NTP issue the server working fine I just run

application reset-config ise

the server now is up