Radius server policy for assign Dynamic VLAN policy is not working

Deepak Kumar — Fri, 21 Feb 2020 18:46:04 GMT

Hi all,

I am facing an issue with Radius server Dynamic assign Policy to user group on Cisco switch.

My switch configuration is below:

interface GigabitEthernet1/0/1
switchport mode access
authentication host-mode multi-host
authentication port-control auto
dot1x pae authenticator

Radius authentication is happening successful but VLAN is not assigned to the port as per Radius server policy.

Here is the debug Output:

Aug 16 03:00:55.705: dot1x-ev:[Gi1/0/1] Interface state changed to UP
Aug 16 03:00:55.709: dot1x-ev:DOT1X Supplicant not enabled on GigabitEthernet1/0/1
Aug 16 03:00:55.786: dot1x-err:AAA auth ready returns Unknown error 0, result = TRUE
Aug 16 03:00:55.786: dot1x_auth Gi1/0/1: initial state auth_initialize has enter
Aug 16 03:00:55.786: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: initialising
Aug 16 03:00:55.786: dot1x_auth Gi1/0/1: during state auth_initialize, got event 0(cfg_auto)
Aug 16 03:00:55.786: @@@ dot1x_auth Gi1/0/1: auth_initialize -> auth_disconnected
Aug 16 03:00:55.786: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: disconnected
Aug 16 03:00:55.786: dot1x_auth Gi1/0/1: idle during state auth_disconnected
Aug 16 03:00:55.786: @@@ dot1x_auth Gi1/0/1: auth_disconnected -> auth_restart
Aug 16 03:00:55.786: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: entering restart
Aug 16 03:00:55.786: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Sending create new context event to EAP for 0xB900001B (705a.0f2c.aee8)
Aug 16 03:00:55.786: dot1x_auth_bend Gi1/0/1: initial state auth_bend_initialize has enter
Aug 16 03:00:55.786: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: entering init state
Aug 16 03:00:55.786: dot1x_auth_bend Gi1/0/1: initial state auth_bend_initialize has idle
Aug 16 03:00:55.786: dot1x_auth_bend Gi1/0/1: during state auth_bend_initialize, got event 16383(idle)
Aug 16 03:00:55.786: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_initialize -> auth_bend_idle
Aug 16 03:00:55.786: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering idle state
Aug 16 03:00:55.786: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Created a client entry (0xB900001B)
Aug 16 03:00:55.786: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Dot1x authentication started for 0xB900001B (705a.0f2c.aee8)
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting !EAP_RESTART on Client 0xB900001B
Aug 16 03:00:55.789: dot1x_auth Gi1/0/1: during state auth_restart, got event 6(no_eapRestart)
Aug 16 03:00:55.789: @@@ dot1x_auth Gi1/0/1: auth_restart -> auth_connecting
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:enter connecting state
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: restart connecting
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting RX_REQ on Client 0xB900001B
Aug 16 03:00:55.789: dot1x_auth Gi1/0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
Aug 16 03:00:55.789: @@@ dot1x_auth Gi1/0/1: auth_connecting -> auth_authenticating
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: authenticating state entered
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:connecting authenticating action
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting AUTH_START for 0xB900001B
Aug 16 03:00:55.789: dot1x_auth_bend Gi1/0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
Aug 16 03:00:55.789: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_idle -> auth_bend_request
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:55.789: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:55.789: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:55.789: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:55.789: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:55.789: dot1x-packet: length: 0x0005
Aug 16 03:00:55.789: dot1x-packet:EAP code: 0x1 id: 0x1 length: 0x0005
Aug 16 03:00:55.789: dot1x-packet: type: 0x1
Aug 16 03:00:55.789: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:55.789: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:idle request action
Aug 16 03:00:56.485: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] queuing an EAPOL pkt on Auth Q
Aug 16 03:00:56.485: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x1
Aug 16 03:00:56.485: dot1x-packet: length: 0x0000
Aug 16 03:00:56.485: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 0,TYPE= 0,LEN= 0

Aug 16 03:00:56.485: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0101.0000
Aug 16 03:00:56.485: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Received an EAPOL-Start packet
Aug 16 03:00:56.488: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x1
Aug 16 03:00:56.488: dot1x-packet: length: 0x0000
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_START on Client 0xB900001B
Aug 16 03:00:56.488: dot1x_auth Gi1/0/1: during state auth_authenticating, got event 4(eapolStart)
Aug 16 03:00:56.488: @@@ dot1x_auth Gi1/0/1: auth_authenticating -> auth_aborting
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting authenticating state
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: entering aborting state
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting AUTH_ABORT for 0xB900001B
Aug 16 03:00:56.488: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 1(authAbort)
Aug 16 03:00:56.488: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_initialize
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: entering init state
Aug 16 03:00:56.488: dot1x_auth_bend Gi1/0/1: idle during state auth_bend_initialize
Aug 16 03:00:56.488: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_initialize -> auth_bend_idle
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering idle state
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting !AUTH_ABORT on Client 0xB900001B
Aug 16 03:00:56.488: dot1x_auth Gi1/0/1: during state auth_aborting, got event 20(no_eapolLogoff_no_authAbort)
Aug 16 03:00:56.488: @@@ dot1x_auth Gi1/0/1: auth_aborting -> auth_restart
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting aborting state
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: entering restart
Aug 16 03:00:56.488: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Resetting the client 0xB900001B
Aug 16 03:00:56.488: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Sending create new context event to EAP for 0xB900001B (705a.0f2c.aee8)
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:restart action for aborting state
Aug 16 03:00:56.488: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting !EAP_RESTART on Client 0xB900001B
Aug 16 03:00:56.492: dot1x_auth Gi1/0/1: during state auth_restart, got event 6(no_eapRestart)
Aug 16 03:00:56.492: @@@ dot1x_auth Gi1/0/1: auth_restart -> auth_connecting
Aug 16 03:00:56.492: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:enter connecting state
Aug 16 03:00:56.492: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: restart connecting
Aug 16 03:00:56.492: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting RX_REQ on Client 0xB900001B
Aug 16 03:00:56.492: dot1x_auth Gi1/0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
Aug 16 03:00:56.492: @@@ dot1x_auth Gi1/0/1: auth_connecting -> auth_authenticating
Aug 16 03:00:56.492: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B: authenticating state entered
Aug 16 03:00:56.492: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:connecting authenticating action
Aug 16 03:00:56.492: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting AUTH_START for 0xB900001B
Aug 16 03:00:56.492: dot1x_auth_bend Gi1/0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
Aug 16 03:00:56.492: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_idle -> auth_bend_request
Aug 16 03:00:56.492: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.492: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.492: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.492: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.492: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.492: dot1x-packet: length: 0x0005
Aug 16 03:00:56.492: dot1x-packet:EAP code: 0x1 id: 0x1 length: 0x0005
Aug 16 03:00:56.492: dot1x-packet: type: 0x1
Aug 16 03:00:56.492: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.492: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:idle request action
Aug 16 03:00:56.506: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.506: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.506: dot1x-packet: length: 0x0017
Aug 16 03:00:56.506: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 1,LEN= 23

Aug 16 03:00:56.506: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.0017
Aug 16 03:00:56.506: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.506: dot1x-packet: length: 0x0017
Aug 16 03:00:56.509: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.509: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.509: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.509: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.509: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.509: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.520: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.520: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.520: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.520: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.520: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.520: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.520: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.520: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.520: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.520: dot1x-packet: length: 0x0006
Aug 16 03:00:56.520: dot1x-packet:EAP code: 0x1 id: 0x2 length: 0x0006
Aug 16 03:00:56.520: dot1x-packet: type: 0x19
Aug 16 03:00:56.523: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.523: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.747: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.747: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.747: dot1x-packet: length: 0x00AA
Aug 16 03:00:56.747: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 170

Aug 16 03:00:56.747: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.00aa
Aug 16 03:00:56.747: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.747: dot1x-packet: length: 0x00AA
Aug 16 03:00:56.747: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.747: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.747: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.747: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.747: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.747: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.757: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.757: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.761: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.761: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.761: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.761: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.761: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.761: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.761: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.761: dot1x-packet: length: 0x05D8
Aug 16 03:00:56.761: dot1x-packet:EAP code: 0x1 id: 0x3 length: 0x05D8
Aug 16 03:00:56.761: dot1x-packet: type: 0x19
Aug 16 03:00:56.761: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.761: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.764: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.764: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.764: dot1x-packet: length: 0x0006
Aug 16 03:00:56.764: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 6

Aug 16 03:00:56.764: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.0006
Aug 16 03:00:56.764: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.764: dot1x-packet: length: 0x0006
Aug 16 03:00:56.764: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.764: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.764: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.764: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.764: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.764: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.771: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.771: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.771: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.771: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.771: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.771: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.771: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.771: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.771: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.771: dot1x-packet: length: 0x020E
Aug 16 03:00:56.771: dot1x-packet:EAP code: 0x1 id: 0x4 length: 0x020E
Aug 16 03:00:56.771: dot1x-packet: type: 0x19
Aug 16 03:00:56.771: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.771: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.785: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.785: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.785: dot1x-packet: length: 0x0097
Aug 16 03:00:56.785: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 151

Aug 16 03:00:56.785: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.0097
Aug 16 03:00:56.785: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.785: dot1x-packet: length: 0x0097
Aug 16 03:00:56.785: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.785: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.785: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.785: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.785: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.785: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.792: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.796: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.796: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.796: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.796: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.796: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.796: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.796: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.796: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.796: dot1x-packet: length: 0x0045
Aug 16 03:00:56.796: dot1x-packet:EAP code: 0x1 id: 0x5 length: 0x0045
Aug 16 03:00:56.796: dot1x-packet: type: 0x19
Aug 16 03:00:56.796: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.796: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.866: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.866: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.866: dot1x-packet: length: 0x0006
Aug 16 03:00:56.866: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 6

Aug 16 03:00:56.866: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.0006
Aug 16 03:00:56.866: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.866: dot1x-packet: length: 0x0006
Aug 16 03:00:56.866: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.866: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.866: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.866: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.866: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.866: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.873: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.873: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.873: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.873: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.873: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.873: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.873: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.873: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.873: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.873: dot1x-packet: length: 0x002B
Aug 16 03:00:56.873: dot1x-packet:EAP code: 0x1 id: 0x6 length: 0x002B
Aug 16 03:00:56.873: dot1x-packet: type: 0x19
Aug 16 03:00:56.873: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.873: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.876: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.876: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.876: dot1x-packet: length: 0x003B
Aug 16 03:00:56.876: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 59

Aug 16 03:00:56.876: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.003b
Aug 16 03:00:56.876: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.876: dot1x-packet: length: 0x003B
Aug 16 03:00:56.876: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.876: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.876: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.876: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.876: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.876: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.883: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.883: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.883: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.883: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.883: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.883: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.883: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.883: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.883: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.883: dot1x-packet: length: 0x003B
Aug 16 03:00:56.883: dot1x-packet:EAP code: 0x1 id: 0x7 length: 0x003B
Aug 16 03:00:56.883: dot1x-packet: type: 0x19
Aug 16 03:00:56.887: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.887: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.887: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.887: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.887: dot1x-packet: length: 0x003B
Aug 16 03:00:56.887: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 59

Aug 16 03:00:56.887: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.003b
Aug 16 03:00:56.887: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.887: dot1x-packet: length: 0x003B
Aug 16 03:00:56.887: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.887: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.887: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.887: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.890: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.890: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.894: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.894: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.894: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.894: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.894: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.894: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.894: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.894: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.894: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.894: dot1x-packet: length: 0x003B
Aug 16 03:00:56.894: dot1x-packet:EAP code: 0x1 id: 0x8 length: 0x003B
Aug 16 03:00:56.897: dot1x-packet: type: 0x19
Aug 16 03:00:56.897: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.897: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.904: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.904: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.904: dot1x-packet: length: 0x006B
Aug 16 03:00:56.904: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 107

Aug 16 03:00:56.908: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.006b
Aug 16 03:00:56.908: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.908: dot1x-packet: length: 0x006B
Aug 16 03:00:56.908: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.908: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.908: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.908: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.908: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.908: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.914: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.914: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.914: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.914: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.914: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.914: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:56.914: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.914: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.914: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.914: dot1x-packet: length: 0x005B
Aug 16 03:00:56.914: dot1x-packet:EAP code: 0x1 id: 0x9 length: 0x005B
Aug 16 03:00:56.914: dot1x-packet: type: 0x19
Aug 16 03:00:56.914: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.914: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.921: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.921: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.921: dot1x-packet: length: 0x002B
Aug 16 03:00:56.921: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 43

Aug 16 03:00:56.921: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.002b
Aug 16 03:00:56.921: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.921: dot1x-packet: length: 0x002B
Aug 16 03:00:56.921: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.921: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.921: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.921: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.921: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.921: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.928: dot1x-sm:[705a.0f2c.aee8,
Switch>
Switch> Gi1/0/1] Posting EAP_REQ for 0xB900001B
Aug 16 03:00:56.928: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 7(eapReq)
Aug 16 03:00:56.928: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_request
Aug 16 03:00:56.928: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.928: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering request state
Aug 16 03:00:56.928: dot1x-ev:[Gi1/0/1] Sending
Switch>
Switch>
Switch>
Switch> EAPOL packet to group PAE address
Aug 16 03:00:56.928: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:56.928: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:56.928: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:56.928: dot1x-packet: length: 0x006B
Aug 16 03:00:56.928: dot1x-packet:EAP code: 0x1 id: 0xB length: 0x006B
Aug 16 03:00:56.928: dot1x-packet: type: 0x19
Aug 16 03:00:56.928: dot1x-pac
Switch>ket:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:56.928: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response request action
Aug 16 03:00:56.942: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Queuing an EAPOL pkt on Authenticator Q
Aug 16 03:00:56.942: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.942: dot1x-packet: length: 0x006B
Aug 16 03:00:56.942: dot1x-ev:[Gi1/0/1] Dequeued pkt: Int Gi1/0/1 CODE= 2,TYPE= 25,LEN= 107

Aug 16 03:00:56.942: dot1x-ev:[Gi1/0/1] Received pkt saddr =705a.0f2c.aee8 , daddr = 0180.c200.0003, pae-ether-type = 888e.0100.006b
Aug 16 03:00:56.946: dot1x-packet:EAPOL pak rx - Ver: 0x1 type: 0x0
Aug 16 03:00:56.946: dot1x-packet: length: 0x006B
Aug 16 03:00:56.946: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAPOL_EAP for 0xB900001B
Aug 16 03:00:56.946: dot1x_auth_bend Gi1/0/1: during state auth_bend_request, got event 6(eapolEap)
Aug 16 03:00:56.946: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_request -> auth_bend_response
Aug 16 03:00:56.946: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering response state
Aug 16 03:00:56.946: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Response sent to the server from 0xB900001B
Aug 16 03:00:56.946: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:request response action
Aug 16 03:00:56.953: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] Received an EAP Success
Aug 16 03:00:56.953: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting EAP_SUCCESS for 0xB900001B
Aug 16 03:00:56.953: dot1x_auth_bend Gi1/0/1: during state auth_bend_response, got event 11(eapSuccess)
Aug 16 03:00:56.953: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_response -> auth_bend_success
Aug 16 03:00:56.953: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting response state
Aug 16 03:00:56.953: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering success state
Aug 16 03:00:56.953: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:response success action
Aug 16 03:00:56.953: dot1x_auth_bend Gi1/0/1: idle during state auth_bend_success
Aug 16 03:00:56.953: @@@ dot1x_auth_bend Gi1/0/1: auth_bend_success -> auth_bend_idle
Aug 16 03:00:56.953: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering idle state
Aug 16 03:00:56.953: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting AUTH_SUCCESS on Client 0xB900001B
Aug 16 03:00:56.953: dot1x_auth Gi1/0/1: during state auth_authenticating, got event 12(authSuccess_portValid)
Aug 16 03:00:56.953: @@@ dot1x_auth Gi1/0/1: auth_authenticating -> auth_authc_result
Aug 16 03:00:56.953: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:exiting authenticating state
Aug 16 03:00:56.953: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering authc result state
Aug 16 03:00:56.953: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAP Key data detected adding to attribute list
Aug 16 03:00:57.704: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to up
Aug 16 03:00:57.984: dot1x-ev:[705a.0f2c.aee8, Gi1/0/1] Received Authz Success for the client 0xB900001B (705a.0f2c.aee8)
Aug 16 03:00:57.984: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] Posting AUTHZ_SUCCESS on Client 0xB900001B
Aug 16 03:00:57.984: dot1x_auth Gi1/0/1: during state auth_authc_result, got event 23(authzSuccess)
Aug 16 03:00:57.984: @@@ dot1x_auth Gi1/0/1: auth_authc_result -> auth_authenticated
Aug 16 03:00:57.984: dot1x-sm:[705a.0f2c.aee8, Gi1/0/1] 0xB900001B:entering authenticated state
Aug 16 03:00:57.984: dot1x-ev:[Gi1/0/1] Sending EAPOL packet to group PAE address
Aug 16 03:00:57.984: dot1x-registry:registry:dot1x_ether_macaddr called
Aug 16 03:00:57.984: dot1x-ev:[Gi1/0/1] Sending out EAPOL packet
Aug 16 03:00:57.984: dot1x-packet:EAPOL pak Tx - Ver: 0x3 type: 0x0
Aug 16 03:00:57.984: dot1x-packet: length: 0x0004
Aug 16 03:00:57.984: dot1x-packet:EAP code: 0x3 id: 0xB length: 0x0004
Aug 16 03:00:57.984: dot1x-packet:[705a.0f2c.aee8, Gi1/0/1] EAPOL packet sent to client 0xB900001B
Aug 16 03:00:58.704: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to up
Switch>

and Radius sever policy as below:

Switch is assigned my default VLAN 1 but I need to be assign vlan 2, which is configured under the Radius server policy in the "Tunnel-pvt-Group-ID-2" attributes.

Regards,

Deepak Kumar

topic Re: Radius server policy for assign Dynamic VLAN policy is not working in Network Access Control

Radius server policy for assign Dynamic VLAN policy is not working

Re: Radius server policy for assign Dynamic VLAN policy is not working

Re: Radius server policy for assign Dynamic VLAN policy is not working

Re: Radius server policy for assign Dynamic VLAN policy is not working

Re: Radius server policy for assign Dynamic VLAN policy is not working