https://community.cisco.com/t5/network-access-control/unable-to-connect-to-desktop-using-juniper-switch/m-p/4045422#M558863 <P><FONT face="verdana,geneva" size="2">Hi Experts,</FONT><BR /><FONT face="verdana,geneva" size="2">I am integrating the Juniper 2200EX running JunOS 15.1r with ISE ver 2.6</FONT><BR /><FONT face="verdana,geneva" size="2">While the authentication via dot1x goes well and the endpoint gets the IP address. The final access is just permit access in authz profile.</FONT><BR /><FONT face="verdana,geneva" size="2">When I try to take a remote desktop from this dot1x enabled port another endpoint, the loses its IP address. The moment I close the remote connection, the endpoint regains the IP address. But, remote desktop is able to take remote of the endpoints which are on non dot1x ports on the same switch.</FONT><BR /><FONT face="verdana,geneva" size="2">There are no ACLs assigned on the interface and access VLAN is applied on the interface.</FONT><BR /><FONT face="verdana,geneva" size="2">I have followed the default configuration from communities from here (<A href="https://community.cisco.com/t5/security-documents/ise-third-party-nad-profiles-and-configs/ta-p/3648719" target="_blank">https://community.cisco.com/t5/security-documents/ise-third-party-nad-profiles-and-configs/ta-p/3648719</A>)</FONT><BR /><BR /><FONT face="verdana,geneva" size="2">I am not sure what I am missing, any insights would be really appreciated.</FONT></P> Fri, 13 Mar 2020 10:41:32 GMT dgaikwad 2020-03-13T10:41:32Z https://community.cisco.com/t5/network-access-control/unable-to-connect-to-desktop-using-juniper-switch/m-p/4045422#M558863 <P><FONT face="verdana,geneva" size="2">Hi Experts,</FONT><BR /><FONT face="verdana,geneva" size="2">I am integrating the Juniper 2200EX running JunOS 15.1r with ISE ver 2.6</FONT><BR /><FONT face="verdana,geneva" size="2">While the authentication via dot1x goes well and the endpoint gets the IP address. The final access is just permit access in authz profile.</FONT><BR /><FONT face="verdana,geneva" size="2">When I try to take a remote desktop from this dot1x enabled port another endpoint, the loses its IP address. The moment I close the remote connection, the endpoint regains the IP address. But, remote desktop is able to take remote of the endpoints which are on non dot1x ports on the same switch.</FONT><BR /><FONT face="verdana,geneva" size="2">There are no ACLs assigned on the interface and access VLAN is applied on the interface.</FONT><BR /><FONT face="verdana,geneva" size="2">I have followed the default configuration from communities from here (<A href="https://community.cisco.com/t5/security-documents/ise-third-party-nad-profiles-and-configs/ta-p/3648719" target="_blank">https://community.cisco.com/t5/security-documents/ise-third-party-nad-profiles-and-configs/ta-p/3648719</A>)</FONT><BR /><BR /><FONT face="verdana,geneva" size="2">I am not sure what I am missing, any insights would be really appreciated.</FONT></P> Fri, 13 Mar 2020 10:41:32 GMT https://community.cisco.com/t5/network-access-control/unable-to-connect-to-desktop-using-juniper-switch/m-p/4045422#M558863 dgaikwad 2020-03-13T10:41:32Z https://community.cisco.com/t5/network-access-control/unable-to-connect-to-desktop-using-juniper-switch/m-p/4045470#M558866 <P>Hey&nbsp;dgaikwad,</P><P>&nbsp;</P><P>Are you permitting all traffic in authz profile? If specific, can you please share your authz profile settings.</P><P>Are you facing issues with Remote desktop connection only? What about the other traffic?</P><P>Also can you please share your switch logs at the time you are testing Remote desktop connection and endpoint is losing it's IP.&nbsp;&nbsp;</P> Fri, 13 Mar 2020 12:11:32 GMT https://community.cisco.com/t5/network-access-control/unable-to-connect-to-desktop-using-juniper-switch/m-p/4045470#M558866 Spooster IT Services 2020-03-13T12:11:32Z