topic Multicasting in DMVPN in Network Security

Multicasting in DMVPN

hussainratlami — Fri, 21 Feb 2020 10:56:32 GMT

Dear All

I had created a DMVPN between 4 diifreent site Hub-Spoke topology, i am using 3com ip phones but i am facing one issue, the issue is i am not able to join confrence (Multiasting) between the spokes, from the hub i can hear both the spoke, but the spoke cannot hear each other. i had enabled ip multicating and Ip pim Saprese-dense mode, the ip telephone comunication between the hub-spoke and spoke-spoke is working, but when i join all in confrence i.e. HUB-Spoke-Spoke it is not working, the hub can hear both but the spoke cannot hear each other.

Please help, its very urgent, thanks in advance

Re: Multicasting in DMVPN

Marwan ALshawi — Tue, 29 Jul 2008 01:28:47 GMT

it sounds tunneling issue i mean when the tunnel in use between the spokes and the hub no comunication happen between the spokes

i havnt faced isues like this

however try to make another tunnel between the spokes and the hub deffrent IPs

and make a static route for packed distend from spok to another spok to go through the new tunnel

but i am not sure

like u hav ealready tunnel0 make tunnel 1

and static route

i route x.x.x.x x.x.x.x interface tunnel 1

where x.x.x.x/x your spoke network

do it on both sides

Good luck

Re: Multicasting in DMVPN

mherald — Thu, 31 Jul 2008 04:59:17 GMT

Can you post you DMVPN specific information? Under the HUB tunnel, do you have plit tunneling turned off? That is the most common reason I have seen for lack of spoke to spoke communication.

Furthermore, do you have it set up for dynamic spoke to spoke (bypass HUB) communication?

Mike

Re: Multicasting in DMVPN

hussainratlami — Thu, 31 Jul 2008 10:00:13 GMT

Thx for your response mike,

I sort out the issue, the issue was with Maping, for confrencing of ip phone work between the hub, i had to create the static map for each spoke on the other spoke, i used command

#ip nhrp map "spoke tunnel address" "spoke Public Address"

ip nhrp map multicast "spoke public Address"

After doing this i was able to see all spoke as each other PIM neibhours.

And multicast calls were establish between all sites.

Once again thx for your response.

Have a Good Day.

Hussain

Re: Multicasting in DMVPN

hussainratlami — Thu, 31 Jul 2008 10:04:31 GMT

Thx for your response Marwanshawi

I sort out the issue, the issue was with Maping, for confrencing of ip phone work between the hub, i had to create the static map for each spoke on the other spoke, i used command

#ip nhrp map "spoke tunnel address" "spoke Public Address"

ip nhrp map multicast "spoke public Address"

After doing this i was able to see all spoke as each other PIM neibhours.

And multicast calls were establish between all sites.

Once again thx for your response.

Have a Good Day.

Hussain

Re: Multicasting in DMVPN

hussainratlami — Thu, 31 Jul 2008 10:05:02 GMT

Thx for your response mike,

I sort out the issue, the issue was with Maping, for confrencing of ip phone work between the hub, i had to create the static map for each spoke on the other spoke, i used command

#ip nhrp map "spoke tunnel address" "spoke Public Address"

ip nhrp map multicast "spoke public Address"

After doing this i was able to see all spoke as each other PIM neibhours.

And multicast calls were establish between all sites.

Once again thx for your response.

Have a Good Day.

Hussain