topic Re: FirePower Management Center GUI/https Not Accessible in Network Security

FirePower Management Center GUI/https Not Accessible

Atasawar1 — Fri, 21 Feb 2020 14:58:01 GMT

Newly installed FMC virtual is not accessible through GUI. I can ping the FMC IP however, GUI is not accessible when I'm trying to reach FMC through https. Output of below commands is attached.

Version: (Cisco_Firepower_Management_Center_VMware-6.2.0-362)

sudo su -
pmtool status | grep “ - “

Thanks in advance for prompt response.

Re: FirePower Management Center GUI/https Not Accessible

Marvin Rhoads — Mon, 18 Dec 2017 02:09:59 GMT

Is your output from the VMware console or are you able to ssh to the server?

Can you share the output of:

netstat-a | grep 443

Re: FirePower Management Center GUI/https Not Accessible

Atasawar1 — Mon, 18 Dec 2017 06:11:31 GMT

It’s from VMware console.

i will share the output once I’m at site.

Thanks

Re: FirePower Management Center GUI/https Not Accessible

Marvin Rhoads — Mon, 18 Dec 2017 06:14:30 GMT

Ok.

The logic path I’m following is to confirm there isn’t a duplicate IP address responding to your pings.

Re: FirePower Management Center GUI/https Not Accessible

Atasawar1 — Mon, 18 Dec 2017 10:18:05 GMT

No this particular IP is not being used anywhere else in the network. I changed the eth0 IP and tried pinging the IP and in that case it was not pingable anymore.

Re: FirePower Management Center GUI/https Not Accessible

Yeremy07 — Tue, 11 Jun 2019 20:27:18 GMT

Hi,

Can you follow the next

pmtool status | grep -E "Waiting|Down|Disable"

pmtool status | grep -i gui

pmtool status | grep -E "Waiting|Down|Disable|Running"

pmtool status | grep sftunnel

Re: FirePower Management Center GUI/https Not Accessible

edjithi83 — Sat, 04 Jan 2020 05:42:16 GMT

Hello,

I had this issue, I fixed it by restarting the console from expert mode.

sudo /etc/rc.d/init.d/console restart

Regards

Djim

Re: FirePower Management Center GUI/https Not Accessible

SaibhuwanSudina70631 — Tue, 30 Aug 2022 11:18:04 GMT

Hi Marvn,

I have came across an issue which is a bit different from this scenarion.

We are using FMC 2500 ( bare metal server USC model ). Our junior engineer have restarted quite a few times today and have observerd this problem.

We are able to loginto the CLI. But GUI is not coming UP.

It is like this. No error and nothing. just a white screen, login page is not coming UP, we have accessed CLI to check and tried few things. They are as below.

/Volume/home/admin# pmtool status | grep -i gui
mysqld (system,gui,mysql) - Running 24404
httpsd (system,gui) - Running 24407
sybase_arbiter (system,gui) - Waiting
vmsDbEngine (system,gui) - Running 24408
ESS (system,gui) - Running 24437
DCCSM (system,gui) - Running 25652
Tomcat (system,gui) - Running 25805
VmsBackendServer (system,gui) - Running 25806
mojo_server (system,gui) - Down

tried these

/etc/rc.d/init.d/pm restart

/Volume/home/admin# pmtool status | grep -i down
Syncd (normal) - Down
expire-session (normal) - Down
Pruner (normal) - Down
ActionQueueScrape (system) - Down
run_hm (normal) - Down
update_snort_attrib_table (normal) - Down
SFTop10Cacher (normal) - Down
mojo_server (system,gui) - Down
RUAScheduledDownload - Period 3600 - Next run Tue Aug 30 10:02:00 2022

/etc/rc.d/init.d/console restart
Stopping Cisco Firepower Management Center 2500......ok
Starting Cisco Firepower Management Center 2500, please wait......started

mojo_server is down. Tried to restart it byy RestartByID, but not running.

no idea what to do. Please suggest how to proceed and any idea what could be the cause for that white screen. Not coming up even after restart.