topic From the FPR chassis manager in Network Security

4110 FTD not registering with FMC

Shahin901 — Fri, 21 Feb 2020 14:01:20 GMT

Hi all,

I have configured a virtual FTD on a 4110 and trying to register the device to the FMC. The 4110 is running FXOS 1.1(4) and the FTD is running 6.0.1 image. I have upgraded the FMC to 6.0.1. I have been trying to register the FTD device to the FMC but no success.
1. does FTD need any license on the FMC rather than regular device license?

2. Does the 4110 need any license on box.

Please suggest if there is anything that I can try.

Really appreciate your help.

Regards,

Your 4110 and FMC both need

Marvin Rhoads — Tue, 21 Feb 2017 03:24:39 GMT

Your 4110 and FMC both need to register with the Cisco Smart Licensing server.

You should then be able to register the FTD virtual device with Smart Licensing and assign the mimimum license level (Threat license) required to apply a policy.

Even without the above, you should still be able to register the device to FMC.

Reference: http://www.cisco.com/c/en/us/td/docs/security/firepower/quick_start/fp4100/ftd-4100-qsg.html#pgfId-180997

Hi Marvin,

Shahin901 — Wed, 22 Feb 2017 04:46:18 GMT

Hi Marvin,

Thank you for your reply.

Is there any prerequisite for the FTD to register to FMC.

Does not matter whatever we try the 4110 FTD logical device would not register with the FMC.

Regards,

Have you assigned the FTD

Marvin Rhoads — Wed, 22 Feb 2017 05:44:27 GMT

Have you assigned the FTD management interface in the 4100 FirePOWER Chassis Manager and then done the initial cli setup on the FTD logical device?

if that is done and the FMC and FTD can reach other on tcp/8305 (if I recall correctly) and the FMC version is greater than or equal to that of the FTD logical device then registration should work.

If there's any NAT in between then it's a bit more complicated.

If you've done all of the above without success then please share the error message you receive.

Hi Marvin,

Shahin901 — Wed, 22 Feb 2017 08:22:05 GMT

Hi Marvin,

Thank you for your reply. What is the initial config on the FTD logical device fron cli.

I have not done any config on the FTD from cli.

Regards,

Sorry - I should have said

Marvin Rhoads — Wed, 22 Feb 2017 11:39:06 GMT

Sorry - I should have said GUI for FTD on 4100 series. Only the FX-OS initial setup is cli-based.

Can you confirm that you have assigned an interface for management to the FTD device? Have you then done the GUI-based configuration of the FirePOWER Threat Defense Image? (General Information, Settings and Agreement tabs).

After having done that does the logical device status indicate it is online? You should also see under Security Device hardware state "up", service state "online", power "on" and application "Cisco FirePOWER Threat Defense".

Finally, check from the FX-OS cli that the FTD device is ready to be managed by FMC. (ssh to your chassis, then "connect ftd" and then "show managers")

From the FPR chassis manager

Shahin901 — Wed, 22 Feb 2017 11:39:07 GMT

From the FPR chassis manager FXOS, every time I connect to the FTD it loops me to enter the admin password.

WMDC-SFR2-A# connect module 1 console
Telnet escape character is '~'.
Trying 127.5.1.1...
Connected to 127.5.1.1.
Escape character is '~'.

CISCO Serial Over LAN:
Close Network Connection to Exit

Firepower-module1>connect ftd
Connecting to ftd console... enter exit to return to bootCLI

System initialization in progress. Please stand by.
You must change the password for 'admin' to continue.
Enter new password:
Confirm new password:
Firepower-module1>?
    show             => Display system information. Enter show ? for options
    config           => Configure the system. Enter config ? for options
    terminalLength   => Terminal settings. Enter terminal ? for options
    ping             => Ping a host to check reachability
    nslookup         => Look up an IP address or host name with the DNS servers
    traceroute       => Trace the route to a remote host
    connect          => Connect to specific csp console (asa, etc)
    support          => System file operations
    debug            => debug commands
    testcrashinfo    => Test crashinfo support
    help             => Get help on command syntax
Firepower-module1>

Firepower-module1>connect ftd
Connecting to ftd console... enter exit to return to bootCLI

System initialization in progress. Please stand by.
You must change the password for 'admin' to continue.
Enter new password:
Confirm new password:
Firepower-module1>

Am I missing some configuration here, cause it does not have the option "show managers".

Regards,

Did you complete the GUI

Marvin Rhoads — Wed, 22 Feb 2017 11:46:08 GMT

Did you complete the GUI-based setup steps I mentioned?

Yes, given the management

Shahin901 — Wed, 22 Feb 2017 12:02:12 GMT

Yes, given the management Interface, IP, FMC IP, Reg key etc. Save and that reloads the FTD Logical Device and everything goes green, up and online.

In your cli session excerpt

Marvin Rhoads — Wed, 22 Feb 2017 16:09:11 GMT

In your cli session excerpt when you typed the "?", it gave show commands as an option. Does it not allow you to enter them?

I can see the following

Shahin901 — Wed, 22 Feb 2017 21:55:19 GMT

I can see the following options after "show" command.

Firepower-module1>
Firepower-module1>?
    show             => Display system information. Enter show ? for options
    config           => Configure the system. Enter config ? for options
    terminalLength   => Terminal settings. Enter terminal ? for options
    ping             => Ping a host to check reachability
    nslookup         => Look up an IP address or host name with the DNS servers
    traceroute       => Trace the route to a remote host
    connect          => Connect to specific csp console (asa, etc)
    support          => System file operations
    debug            => debug commands
    testcrashinfo    => Test crashinfo support
    help             => Get help on command syntax
Firepower-module1>show ?
    diskusage        => Display current disk space usage
    time             => Display current system date and time
    memoryusage      => Display the system Memory usage
    cpuinfo          => Display the system CPU Information
    users            => Display who is logged on and user operations
    uptime           => Display system up time
    slot             => Display the slot number of SSP to which this blade is connected
    processes        => Display all system processes
    hosts            => Show hosts
    route            => Show configured routes
    interfaces       => Show currently configured interfaces
    version          => Display product version
    netstat          => Show network connections
    vnicmap          => Display VNICs with Ethernet interfaces
    platform         => Display platform information
    memory           => Display the memory monitor configuration
    disk             => Display the disk monitor configuration
    cpu              => Display the CPU monitor configuration
    ntp              => Show NTP time sync information
    coredump         => Show coredump configuration
    maxRestart       => Show maxRestart
    services         => Display status of the services
    process          => Show process details
    tech-support     => Generate system information report for troubleshooting purposes
Firepower-module1>

Since the device is brand new

Marvin Rhoads — Thu, 23 Feb 2017 02:41:58 GMT

Since the device is brand new, could you try upgrading the FX-OS to the current release 2.1.1 and reimaging the FTD logical device to 6.2?

I don't see any documented bugID that describes what you are seeing but you are woirking with the very first software release for the FTD image. Think of it as "1.0".

HI Marvin,

Shahin901 — Thu, 23 Feb 2017 03:56:51 GMT

HI Marvin,

Thank you for the suggestion.

I have upgraded the FX-OS to 2.0.1 and that is a prerequisite of 2.1.1.

My FMC is currently running 6.0.1, do I need to upgrade the FMC to 6.2 as the FTD will be running 6.2 code.

Regards

Yes - FMC 6.2 (or higher) is

Marvin Rhoads — Thu, 23 Feb 2017 04:17:46 GMT

Yes - FMC 6.2 (or higher) is required to manage FTD 6.2 devices.

Hi Marvin,

Shahin901 — Mon, 13 Mar 2017 00:03:31 GMT

Hi Marvin,

Sorry forgot to Thank you for all the inputs.

Once I upgraded FXOS, FTD and FMC to the latest versions, the issue was resolved.

Regards,