topic OOO!! THANKS!!! One question! in Network Security

Reinstall sourcefire.Licence.

n.avramenko87 — Tue, 12 Mar 2019 13:02:50 GMT

I want to reinstall sourcefire. How I can move the licence? Thank you!

Hi,

ankojha — Thu, 23 Jun 2016 13:24:48 GMT

Hi,

If you are reimaging the version on sourcefire, then you don't need to worry about licenses, it remains the same and you don't need to move but if you are going for replacement then you need to email to licensing@cisco.com with your new license key so that they can bind the same licenses to new device.

Rate if it helps.

thanks,

Ankita

Hello Team,

Jetsy Mathew — Thu, 23 Jun 2016 15:36:11 GMT

Hello Team,

Are you going to reinstall the Firesight Management Center ? If the firesight management gets reinstalled and the license keys gets changed, then you have to regenerate the license.

Navigate to System > license > Add new license and in version 6.0 System > license > Classic License > Add new license , you can see a license key over there. Based on the license key only , the licensing team generates the license for the device.Thus note the license key and if its gets changed, then only contact the Licensing team under the following contact number.

Licensing : +1 919-574-1701

If its a virtual firesight management center, then you have to redeploy the VM. In VM , if the MAC address gets changed (if its not manual MAC ) then you have to request the Licensing team to regenerate the License based on the new key.

Rate if this post helps you

Regards

Jetsy

THANK YOU! What I whant. A

n.avramenko87 — Fri, 24 Jun 2016 06:56:24 GMT

THANK YOU! What I whant. A have virtual firesight center, it has licence but it has some problems with work. I whant to try shutdown this virtual center and install new virtual center. I want to see how it will work.Can i input licence to new virtual machine (licence a see in my account on portal)?

Hello Team,

Jetsy Mathew — Fri, 24 Jun 2016 10:43:06 GMT

Hello Team,

If you need to redeploy the Virtual FMC then first of all you need to verify that you are using manual or automatic MAC in the Virtual Machine.

Power off the Virtual Machine and go to the settings and make a note of your MAC address.

If the MAC starts with 00:50:56 then it’s a manual MAC and you can give the same MAC after redeploying the FMC.

Redeploy the VM using the image for the virtual appliance.

Disable the option “power on the Virtual Machine after redeploy” .

Finish re-deploying the device.

Go to the Virtual Machine settings and change the option of MAC to manual and provide the same MAC as follows - 00:50:56:xx:xx:xx which you already noted before redeploy. Add that MAC address and save it. (MAC address provided is just a sample )

Power on the Virtual Machine

Later we will add the sensor.

If the MAC is not manual MAC, after redeploy we should contact the Licensing team with the new MAC address to regenerate the license for the same.

Rate if this answer helps you.

Regards

Jetsy

OOO!! THANKS!!! One question!

n.avramenko87 — Fri, 24 Jun 2016 12:58:15 GMT

OOO!! THANKS!!! One question! If i will have problems on new FMC can i shutdown it and start old FMC.Is it old FMS saved old settings?

Hello Team,

Jetsy Mathew — Fri, 24 Jun 2016 13:02:09 GMT

Hello Team,

Unless you reinstall it , the settings will not be wiped 🙂 Thus if you still need the old one , you can use it.

Whenever you reinstall the FMC ,usually there wont be any issues.

Rate if my post helps you.

Happy weekend.

Reagrds

jetsy

Thank you! You cool!

n.avramenko87 — Fri, 24 Jun 2016 13:16:31 GMT

Thank you! You cool!

Cheers..

Jetsy Mathew — Fri, 24 Jun 2016 13:19:55 GMT

Cheers..

Hello Team,

Jetsy Mathew — Mon, 27 Jun 2016 03:55:43 GMT

Hello Team,

Hope your queries are clear .

Please rate and mark the answer correct if my posts helped you.

Regards

Jetsy