topic Re: You don't need a license to in Network Security

ASA FirePOWER Configuration tab missing in ASA5506

kelvin.lui11 — Tue, 12 Mar 2019 07:43:33 GMT

Hi all,

The ASA FirePOWER Configuration tab missing in ASDM,How do i get the license key to activate the firepower service?Thank you.

(No subject)

kelvin.lui11 — Mon, 09 May 2016 04:18:13 GMT

You don't need a license to

Karsten Iwen — Mon, 09 May 2016 06:57:24 GMT

You don't need a license to see the FirePOWER tab in ASDM. You just have to do the install/base-configuration of the module and the FirePOWER Tab will appear. After that you apply the licenses inside of the FirePOWER Tab of ASDM.

To proceed further:

Do you have the CONTROL-License? Should be a paker-PAK inside the ASA box.
What is the actual state of the module? Paste the output of "show module sfr details"

A couple of points which may

davidfield — Tue, 10 May 2016 08:11:03 GMT

A couple of points which may help as I've setup a few 5506s.

- Run the config wizard and ensure you assign the Firepower Module an IP

- You need an ethernet in the mgmt interface. So a basic interface setup would be

g1/1 - WAN,

g1/2 - the Inside network ethernet to local switch - IP 192.168.0.1

Mgmt - the Inside network ethernet to local switch - IP 192.168.0.2

If you can ping the mgmt IP then you should be able to start ASDM and it will connect to the Firewpower module.

Note after a reboot it takes a few minutes for the Firepower module to start so wait a bit before starting ASDM. ASDM may prompt you to verify the firepower address and port.

You can then go to the licensing tab and apply the control license using the PAK in the box.

Dave

Just deployed mine and I was

Richard Benfatto — Sat, 30 Jul 2016 09:16:38 GMT

Just deployed mine and I was pulling my hair on this one............will try............from Lidcombe with love.....................

Re: You don't need a license to

peni.nscg — Wed, 22 Nov 2017 05:00:30 GMT

Hi Karsten,

We have a missing Firepower config tab when we login to ASDM. Below is the output from show mod sft det command.

------------------------

RBF-IFW-ASA# sh module sfr details
Getting details from the Service Module, please wait...

Card Type: FirePOWER Services Software Module
Model: ASA5516
Hardware version: N/A
Serial Number: JAD202407BK
Firmware version: N/A
Software version: 5.4.1-211
MAC Address Range: 00f6.6347.8726 to 00f6.6347.8726
App. name: ASA FirePOWER
App. Status: Up
App. Status Desc: Normal Operation
App. version: 5.4.1-211
Data Plane Status: Up
Console session: Ready
Status: Up
DC addr: No DC Configured
Mgmt IP addr: 192.168.45.45
Mgmt Network mask: 255.255.255.0
Mgmt Gateway: 192.168.45.1
Mgmt web ports: 443
Mgmt TLS enabled: true

--------------------------------

Re: You don't need a license to

dm — Fri, 16 Mar 2018 11:56:25 GMT

Have the same problem with brand new 5506-X.

Any solution?

Re: You don't need a license to

dm — Mon, 19 Mar 2018 11:26:56 GMT

OK. This was quite simple, but hard to find: dm@dm:~$ java -version java version "1.8.0_161" Java(TM) SE Runtime Environment (build 1.8.0_161-b12) Java HotSpot(TM) 64-Bit Server VM (build 25.161-b12, mixed mode) works 151, from Ubuntu 17.10 repo, does not.

Re: You don't need a license to

Slippy_Skin — Mon, 04 May 2020 11:40:48 GMT

Another way is to;

Close ASDM

Load Java (Control Panel in Windows)

(Temporary Internet Files) - Settings, Delete Files, (Just select the top two - so Trace and Log Files and Cashed Applications and Applets)

Open ASDM

Re: ASA FirePOWER Configuration tab missing in ASA5506

CDHIB — Mon, 06 May 2024 07:06:51 GMT

Anybody found a solution yet on this?

Re: ASA FirePOWER Configuration tab missing in ASA5506

balaji.bandi — Mon, 06 May 2024 07:57:54 GMT

Anybody found a solution yet on this?

can you open a new discussion referring this thread and explaining your environment in brief.

if you running ASA version mentioned below not supported so you need to downgrade :

Important Notes

https://www.cisco.com/c/en/us/td/docs/security/asa/asa910/release/notes/asarn910.html