topic Re: Cisco ASA - Configuration of Active standby failover in Network Security

Cisco ASA - Configuration of Active standby failover

LovejitSingh1313 — Tue, 25 Aug 2020 23:29:30 GMT

Hello Experts

I want to configure two ASA in failover. Right Now both primary ASA is working and I connected secondary ASA with Internet and LAN and DMZ interface and configured the interfaces but nothing else is configured as it will get config from the primary. Please advise step by step with configuration.

Also, what is the command to switch the Active firewall to standby and vice-versa?(I do not want to change the role from Primary to Secondary of the unit instead just want to switch Active to standby manually)

Thanks,

Re: Cisco ASA - Configuration of Active standby failover

LovejitSingh1313 — Wed, 26 Aug 2020 00:23:40 GMT

Hello Guys @Rob Ingram @balaji.bandi @Marvin Rhoads @Georg Pauwen

I configured failover by using following link and its working great. I was also able to switch standby unit to Active as well.

https://www.petenetlive.com/KB/Article/0000048

Failover is working great but i am not able to understand the #sh failover command output. Please see the Colored text and what does (Not-Monitored) means?

ciscoasa# sh failover
Failover On
Failover unit Primary
Failover LAN Interface: FAILOVER GigabitEthernet0/5 (up)
Reconnect timeout 0:00:00
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 1 of 61 maximum
MAC Address Move Notification Interval not set
Version: Ours 9.12(2), Mate 9.12(2)
Serial Number: Ours 9AREQ9MVUPW, Mate 9ANWQD7GDN9
Last Failover at: 00:15:56 UTC Aug 26 2020
This host: Primary - Active
Active time: 185 (sec)
slot 0: ASAv hw/sw rev (/9.12(2)) status (Up Sys)
Interface outside (192.168.2.121): Normal (Monitored)
Interface inside (10.10.10.1): Normal (Not-Monitored)
Interface guestWIFI (20.20.20.1): Normal (Not-Monitored)
Other host: Secondary - Standby Ready
Active time: 303 (sec)
Interface outside (192.168.2.123): Normal (Monitored)
Interface inside (10.10.10.3): Normal (Not-Monitored)
Interface guestWIFI (20.20.20.3): Normal (Not-Monitored)

Stateful Failover Logical Update Statistics
Link : Unconfigured.

Thanks,

Re: Cisco ASA - Configuration of Active standby failover

balaji.bandi — Wed, 26 Aug 2020 00:35:28 GMT

Those interfaces not configured to monitor - if it is your requirement enable to monitor

failover trigger places based on criteria met :

https://community.cisco.com/t5/security-documents/asa-interface-monitoring-in-failover-and-its-impact/ta-p/3144324

good HA document for reference - in case anything missing :

https://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/ha_failover.html#35064

Re: Cisco ASA - Configuration of Active standby failover

Mohammed al Baqari — Wed, 26 Aug 2020 07:24:58 GMT

Hi,

Monitored interfaces will trigger failover if any of them fail.
Non-monitored interfaces will not trigger failover if they fail.

**** please remember to rate useful posts

Re: Cisco ASA - Configuration of Active standby failover

AmmarHermiz14196 — Fri, 04 Sep 2020 17:19:41 GMT

Hi,

I have an ASA 5506-X want to configure it after a Verizon router model number (G1100).
I have block of 5 static IP address.

Anything I need to change on Verizon Router?

I will appreciate your help with this.

Thanks,

Ammar

Re: Cisco ASA - Configuration of Active standby failover

balaji.bandi — Fri, 04 Sep 2020 19:28:21 GMT

I have never worked with that router , but it is possible as suggested below post : (if you can make ISP router in Bridge mode and make ASA as in path is good suggestion)

https://community.cisco.com/t5/network-security/asa-5505-with-fios/m-p/2296660/highlight/true