https://community.cisco.com/t5/network-security/mid-term-help/m-p/4578650#M1088631 <P>Thank you, I have done everything from the word document but there are still red triangles from R1 to R3 and from R1 to S1. Could you check it over for me to make sure it is all there?&nbsp;</P> Fri, 25 Mar 2022 17:11:55 GMT Skyamoebe551 2022-03-25T17:11:55Z https://community.cisco.com/t5/network-security/mid-term-help/m-p/4564754#M1087975 <P>Hello,&nbsp;</P><P>I think I understand what is needing to be done here with erasing all setting and resetting them with what is on the word document but there is something about the ACL I am not quiet sure about. I could use some help or feed back please and thank you!</P><P>&nbsp;</P><P>I have attached the unedited packet tracer and word document.&nbsp;</P> Sun, 06 Mar 2022 02:24:51 GMT https://community.cisco.com/t5/network-security/mid-term-help/m-p/4564754#M1087975 Skyamoebe551 2022-03-06T02:24:51Z https://community.cisco.com/t5/network-security/mid-term-help/m-p/4565307#M1087978 <P>What part of the assessment are you in doubt with ?&nbsp;</P><P>Is it only part7</P><P>restricting access to the vty lines.&nbsp;</P> Mon, 07 Mar 2022 10:13:48 GMT https://community.cisco.com/t5/network-security/mid-term-help/m-p/4565307#M1087978 carstenlymann1 2022-03-07T10:13:48Z https://community.cisco.com/t5/network-security/mid-term-help/m-p/4565941#M1088002 <P>&nbsp;</P> <P>VTY line ACL is tricky a bit;&nbsp; 1. access class in use source IP in ACL but access -class out which uses destination in standard ACL</P> <P>Configure a named access list to only allow R1 to telnet to R2</P> <P>Apply the named ACL to the VTY lines and use Named ACL <STRONG>ADMIN-MGT</STRONG></P> <P style="-qt-block-indent: 0; text-indent: 0px; margin: 0px;"><EM>line vty 0 15</EM></P> <P style="-qt-block-indent: 0; text-indent: 0px; margin: 0px;"><EM>access-class ADMIN-MGT in</EM></P> <P style="-qt-block-indent: 0; text-indent: 0px; margin: 0px;"><EM>ip access-list standard ADMIN-MGT<BR /></EM></P> <P style="-qt-block-indent: 0; text-indent: 0px; margin: 0px;"><EM>permit host [IP of R1 here]</EM></P> <P>Allow telnet access to VTY lines</P> <P style="-qt-block-indent: 0; text-indent: 0px; margin: 0px;"><EM>transport input telnet</EM></P> <P style="-qt-block-indent: 0; text-indent: 0px; margin: 0px;">&nbsp;</P> <P style="-qt-block-indent: 0; text-indent: 0px; margin: 0px;"><EM>Regards, ML<BR />**Please Rate All Helpful Responses **</EM></P> Tue, 08 Mar 2022 02:12:59 GMT https://community.cisco.com/t5/network-security/mid-term-help/m-p/4565941#M1088002 Martin L 2022-03-08T02:12:59Z https://community.cisco.com/t5/network-security/mid-term-help/m-p/4578650#M1088631 <P>Thank you, I have done everything from the word document but there are still red triangles from R1 to R3 and from R1 to S1. Could you check it over for me to make sure it is all there?&nbsp;</P> Fri, 25 Mar 2022 17:11:55 GMT https://community.cisco.com/t5/network-security/mid-term-help/m-p/4578650#M1088631 Skyamoebe551 2022-03-25T17:11:55Z