topic Re: Restored FMC from backup. Can't see or deploy to devices? in Network Security

Restored FMC from backup. Can't see or deploy to devices?

andrew.webster — Wed, 25 Jan 2023 15:25:20 GMT

hi,

Issue:

Had to rebuild and restore a vmware FMC from an old backup. Now but my FMC won't upgrade and can't connect to Devices?

My vmware FMC running 7.0.3 had an issue with its database and TAC recommended to restore from a backup.

Built a new vmware FMC running 7.0.3 and attempted to restore my backup. The backup runs and eventually returns with the task notification, 'Unable to restore CSM'.

I have tried this many times with 7.0.3 backups taken from different dates. Same result.

I built another new vmware FMC running 7.0.1 and restore an old backup taken when running 7.0.1.

This restore completes successfully and I see all my FMC settings restored.

Go to Devices page and all my devices show that they're offline.

The Devices are not offline they are happily passing traffic? They are reachable, they are on the same L2 vlan as the FMC.

Next I attempt to upgrade from 7.0.1 to 7.0.3

When attempting to upgrade on the Product Updates webpage I see the error,

'Device configurations are out-of-date. Deploy configurations.'

I cannot select the FMC it is greyed out, the 'Install' button is also greyed out.

I attempt to go to Devices and Deploy to one of my devices.

Deploy fails with error, 'Deployment failed due to communications failure with device. If problem persists after retrying later, contact Cisco TAC'.

Tried multiple times to deploy to device, fails with the same error.

I am stuck.

I need the FMC to function again so that I can continue to deploy rule changes to our Devices.

Any ideas what to try next?

Re: Restored FMC from backup. Can't see or deploy to devices?

andrew.webster — Wed, 25 Jan 2023 17:42:01 GMT

Ok,

going through this doc to troubleshoot why my new FMC can't see my devices.

Configure, Verify and Troubleshoot Firepower Device Registration - Cisco

I get to 'show managers' on my Devices and, nothing shows up?

It is like the devices lost their config for the FMC connection?
I don't understand, these were all connected prior to my attempts to restore my FMC backup.

No changes on the devices.

How does this happen with only an FMC restore?

Re: Restored FMC from backup. Can't see or deploy to devices?

Marius Gunnerud — Thu, 26 Jan 2023 07:40:51 GMT

I have rebuilt and restored backups for several FMCs without any issues. You might be hitting a bug and I would recommend opening a TAC case to troubleshoot this further.

The times when I have had to rebuild FMCs, I just built the FMC with the same image version as the previous, connected to the remote storage repository, and then restored backup. done and dusted. Did not have to deploy or anything more.

Re: Restored FMC from backup. Can't see or deploy to devices?

khorram1998 — Thu, 26 Jan 2023 08:50:25 GMT

It sounds like there may be some issues with the restored backup and the current state of the devices. One thing to check is that the backup was taken from the same version of FMC as the one you are restoring to. Additionally, check that the devices that were backed up are the same devices that are currently being managed by the FMC.

Another thing to check is the network connectivity between the FMC and the devices. Ensure that the FMC has the correct IP address and that there is no firewall or other network configuration blocking communication between the FMC and the devices.

You may also want to try resetting the devices to their factory defaults, then re-registering them with the FMC and deploying the configuration again.

If the issue persists, it might be worth opening a TAC case for further troubleshooting and assistance.

Please rate this and mark as solution/answer, if this resolved your issue
All the best,
AK

Re: Restored FMC from backup. Can't see or deploy to devices?

Massimo Baschieri — Fri, 27 Jan 2023 05:26:19 GMT

..or the devices version is higher than the one on the fmc

Re: Restored FMC from backup. Can't see or deploy to devices?

balaji.bandi — Fri, 27 Jan 2023 05:53:14 GMT

Adding to other posters - what is the version of FTD?

Has this FMC was in the same DC or EsXI work Group ( may be precise same VLAN or IP Range)

If the FMC IP changed and ARP not flushed - that need to check ? From FMC Cli are you able to ping FTD ?

If you see all the config in FMC like object and ACP other stuff,

Try to deregister one of the FTD and re-register and for testing push a test policy.

Re: Restored FMC from backup. Can't see or deploy to devices?

andrew.webster — Wed, 12 Apr 2023 21:35:50 GMT

Update in case a web search leads anyone else here with the same issue:

Here is the fix: Engage tac, escalate.

There is no way I would have found the fix on my own.