topic Re: ASA5506-X Firepower services not show in ASDM in Network Security

ASA5506-X Firepower services not show in ASDM

INEMINEMINEMINEM — Fri, 05 May 2023 20:47:40 GMT

Hello,

I'm facing an issue with a ASA5506-X with Firepower Services that I need help from the community to solve.

The situation is that I try to manage the firewall from ASDM without FMC, but the tab "ASAFirepower configurations" not show up and I cannot figure out what I need to do to fix the issue.

> show managers
Managed locally.

> show interfaces
---------------------[ inside ]---------------------
Physical Interface : Port-channel1
Type : ASA
Security Zone : None
Status : Enabled
Load Balancing Mode : N/A
---------------------[ cplane ]---------------------
IPv4 Address : 127.0.2.1
----------------------[ eth0 ]----------------------
Physical Interface : eth0
Type : Management
Status : Enabled
MDI/MDIX : Auto
MTU : 1500
MAC Address : 00:27:E3:04:CA:A2
IPv4 Address : 192.168.1.251
----------------------[ tun1 ]----------------------
IPv6 Address : fdcc::bd:0:ffff:a9fe:1/64
---------------------[ tunl0 ]----------------------
----------------------------------------------------

Show> network
===============[ System Information ]===============
Hostname : firepower
Domains : example.net
Management port : 8305
IPv4 Default route
Gateway : 192.168.1.1

======================[ eth0 ]======================
State : Enabled
Channels : Management & Events
Mode : Non-Autonegotiation
MDI/MDIX : Auto/MDIX
MTU : 1500
MAC Address : 00:27:E3:04:CA:A2
----------------------[ IPv4 ]----------------------
Configuration : Manual
Address : 192.168.1.251
Netmask : 255.255.255.0
Broadcast : 192.168.1.255
----------------------[ IPv6 ]----------------------
Configuration : Disabled

===============[ Proxy Information ]================
State : Disabled
Authentication : Disabled

From ASA FirePower Status I can read -> Connect to the ASA FirePOWER application: https://No_DC_Configured (image attached).

What should I do to fix that?

Thanks in advanced.

Re: ASA5506-X Firepower services not show in ASDM

MHM Cisco World — Fri, 05 May 2023 20:58:02 GMT

First i need to see asa inside and management config

Also I need to see

Debug http 255

Re: ASA5506-X Firepower services not show in ASDM

INEMINEMINEMINEM — Fri, 05 May 2023 21:20:20 GMT

Sure, let me share with you:

interface Management1/1
management-only
nameif mgmt
security-level 0
ip address 192.168.1.251 255.255.255.0
!

interface Port-channel1
lacp max-bundle 8
shutdown
nameif inside
security-level 100
no ip address
!

Port-channel1 that will be the inside interface not have yet any ip address assigned. I access the ASDM via mgmt interface 192.168.1.251 connected directly to mgmt Port on ASA.

The debug http 255 file I attached.

Thanks in advance.

Re: ASA5506-X Firepower services not show in ASDM

MHM Cisco World — Fri, 05 May 2023 21:30:46 GMT

https://www.cisco.com/c/en/us/support/docs/security/adaptive-security-device-manager/200889-Using-ASDM-to-manage-a-FirePOWER-module.html

Yes I guess this is problem here,
you need to access ASDM through the inside interface because the management interface is NOW not represent ASA it represent firepower.
check link above.

Re: ASA5506-X Firepower services not show in ASDM

INEMINEMINEMINEM — Fri, 05 May 2023 21:51:51 GMT

Of course, problem solved, thank you very much for your help!