https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281174#M1120607 <P>As you can see on the screenshot you shared in that Interface section you have both the security zones as well as the interfaces groups. Just as a side note apart from the name change, depending on what you are configuring, you might need to use security zones or interface groups. For instance if you are configuring NetFlow on the FMC platform settings policies, then the only option to use when you configure the collecotrs would be the interface groups. More about this here in the following link:</P> <P><A href="https://docs.defenseorchestrator.com/cdfmc/t_creating_security_zone_and_interface_group_objects.html#!c_security_zones.html" target="_blank">Security Zones and Interface Groups</A></P> Mon, 14 Apr 2025 14:29:56 GMT Aref Alsouqi 2025-04-14T14:29:56Z https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281027#M1120601 <P>Hi CISCO DEV team</P><P>Can we please keep security zone under objects on FMC?</P><P>&nbsp;</P><P>before I upgraded to 7.4.2, There was security zone under objects on FMC, later, you give it a new name "interface" instead of security zone. you make things complicated. it was not good.</P> Mon, 14 Apr 2025 06:08:55 GMT https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281027#M1120601 Ben Ss 2025-04-14T06:08:55Z https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281061#M1120602 <P>Zones have not gone away. They are integral to FTD Access Control Policies. They should also not have been lost as part of any upgrade. I have upgraded dozens of FTDs without encountering this behavior. I suggest you open a TAC case for investigation.</P> Mon, 14 Apr 2025 08:35:26 GMT https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281061#M1120602 Marvin Rhoads 2025-04-14T08:35:26Z https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281174#M1120607 <P>As you can see on the screenshot you shared in that Interface section you have both the security zones as well as the interfaces groups. Just as a side note apart from the name change, depending on what you are configuring, you might need to use security zones or interface groups. For instance if you are configuring NetFlow on the FMC platform settings policies, then the only option to use when you configure the collecotrs would be the interface groups. More about this here in the following link:</P> <P><A href="https://docs.defenseorchestrator.com/cdfmc/t_creating_security_zone_and_interface_group_objects.html#!c_security_zones.html" target="_blank">Security Zones and Interface Groups</A></P> Mon, 14 Apr 2025 14:29:56 GMT https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281174#M1120607 Aref Alsouqi 2025-04-14T14:29:56Z https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281206#M1120608 <P>Further, zones and interfaces groups have always been listed under Interface objects. Here is a link to the 7.0 documentation confirming the same:</P> <P><A href="https://www.cisco.com/c/en/us/td/docs/security/firepower/70/configuration/guide/fpmc-config-guide-v70/reusable_objects.html?bookSearch=true#concept_0E473FB2A86E477295C7EAB9F7CECDD7" target="_blank" rel="noopener">https://www.cisco.com/c/en/us/td/docs/security/firepower/70/configuration/guide/fpmc-config-guide-v70/reusable_objects.html?bookSearch=true#concept_0E473FB2A86E477295C7EAB9F7CECDD7</A></P> <P>...and from 6.2.3:</P> <P><A href="https://www.cisco.com/c/en/us/td/docs/security/firepower/623/configuration/guide/fpmc-config-guide-v623/reusable_objects.html?bookSearch=true#ID-2243-000009b4" target="_blank">https://www.cisco.com/c/en/us/td/docs/security/firepower/623/configuration/guide/fpmc-config-guide-v623/reusable_objects.html?bookSearch=true#ID-2243-000009b4</A></P> Mon, 14 Apr 2025 15:57:39 GMT https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5281206#M1120608 Marvin Rhoads 2025-04-14T15:57:39Z https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5282250#M1120628 <P>Thank you.</P> Thu, 17 Apr 2025 08:32:20 GMT https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5282250#M1120628 Ben Ss 2025-04-17T08:32:20Z https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5303355#M1121495 <P>What would really help and this and other scenarios would be the ability to bulk edit the zone in ACP and NAT policies in FMC.</P> Fri, 27 Jun 2025 11:25:02 GMT https://community.cisco.com/t5/network-security/keep-security-zone-on-fmc/m-p/5303355#M1121495 grant.maynard 2025-06-27T11:25:02Z