topic I added a NAT ID , the in Network Security

Unable to add second device - FireSIGHT Mnagament Center

aoun.ameur1 — Tue, 12 Mar 2019 06:51:11 GMT

Hi All,

I tried to add a second asa5515x to the firesight management center but it indicates that is not allowed

I have added the manager in cli command line :

conf manager add à.@.@.@.@ cisco123

Is there any suggestion?

Which error do you get?

Karsten Iwen — Mon, 09 Nov 2015 18:24:01 GMT

Which error do you get?

In case the ASA sfr is behind

Rishabh Seth — Tue, 10 Nov 2015 06:59:36 GMT

In case the ASA sfr is behind a NAT device then use the NAT id in "manager add" configuration.

Refer following link:

http://www.cisco.com/c/en/us/support/docs/security/asa-firepower-services/118824-configure-firepower-00.html

Also provide the information requested by Karsten.

Thanks,

R.Seth

I added a NAT ID , the

aoun.ameur1 — Tue, 10 Nov 2015 07:56:05 GMT

I added a NAT ID , the command is as-below :

configure manager add @ip of the firesight cisco123 123456

In firesight, i try to add the device, but it indicates :

Could not establish a connection with sensor. Make sure the registration keys match, that the software versions are compatible, and that the network is not blocking the connection.

I had a similar issue and it

Massimo Baschieri — Tue, 10 Nov 2015 08:10:18 GMT

I had a similar issue and it turned out that the device was inadvertently powered off during an upgrade, maybe this way the device boots up in an unstable state.

After a reimaging I was able to regularly associate the asa to defence center.

Thanks Massino,

aoun.ameur1 — Tue, 10 Nov 2015 08:26:53 GMT

Thanks Massino,

I will try to reimage the software module so !

what is the output of the

Karsten Iwen — Tue, 10 Nov 2015 08:40:24 GMT

what is the output of the following command?

sh module sfr details

I have this :

aoun.ameur1 — Tue, 10 Nov 2015 10:05:52 GMT

I have this :

Card Type: FirePOWER Services Software Module
Model: ASA5515
Hardware version: N/A
Serial Number: FCH19367YGE
Firmware version: N/A
Software version: 5.3.1-152
MAC Address Range: e4aa.5d41.e07c to e4aa.5d41.e07c
App. name: ASA FirePOWER
App. Status: Up
App. Status Desc: Normal Operation
App. version: 5.3.1-152
Data Plane Status: Down
Console session: Ready
Status: Up
DC addr: No DC Configured
Mgmt IP addr: 10.10.100.111
Mgmt Network mask: 255.255.0.0
Mgmt Gateway: 10.10.100.105
Mgmt web ports: 443
Mgmt TLS enabled: true

I have to add two devices in firesight management center. I succed in adding the first with@ip 10.10.100.104 and registration key cisco but i cannot add the second with @ip 10.10.100.105 and a registration key cisco123

Are you running at least 9.2

Karsten Iwen — Tue, 10 Nov 2015 10:06:08 GMT

Are you running at least 9.2(2) on your ASA?

Yes , in two ASA , there is

aoun.ameur1 — Tue, 10 Nov 2015 10:18:53 GMT

Yes , in two ASA , there is ASA9.2(4) version