topic Hi, I have a problem, I don't in Network Security

ASA 5506W wifi setup problem

erikorrsjo — Tue, 12 Mar 2019 06:21:06 GMT

Hello,

I have problems getting to the webinterface for configuring the ASA5506W wifi.

According to the documentation, the access point should get the IP-address 192.168.10.2.

I can't reach that IP from a computer on the "inside"-interface of the ASA. Pinging the IP from the ASA does not work either.

I read somewhere that reseting the wifi-device using

hw-module module wlan recover configuration

would help, but it didn't do anything for me.

Anyone got any suggestions?

/Erik

Hi Erik.Did you solve this

Henrik Rostgaard Soerensen — Wed, 16 Sep 2015 13:03:25 GMT

Hi Erik.

Did you solve this issue ?

I'm in the same situation.

/Henrik

Hi,Can you post the config

Vibhor Amrodia — Thu, 17 Sep 2015 10:54:39 GMT

Hi,

Can you post the config from the ASA device ?

Thanks and Regards,

Vibhor Amrodia

Sure Vibhor.Here you are.

Henrik Rostgaard Soerensen — Thu, 17 Sep 2015 13:06:14 GMT

Sure Vibhor.

Here you are.

/henrik

Hi Enrik, Try following:hw

Rishabh Seth — Thu, 17 Sep 2015 13:57:24 GMT

Hi Enrik,

Try following:

hw-module module wlan recover configuration

asa# session wlan console

ap>enable
Password: Cisco
ap#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

ap(config)#ip default-gateway 192.168.10.1
ap#copy run start

Then try accessing the wlan GUI.

Hope it helps!!!

Thanks,

R.Seth

Thanks R.SethI'll try this on

Henrik Rostgaard Soerensen — Thu, 17 Sep 2015 20:53:17 GMT

Thanks R.Seth

I'll try this on monday then I'm at the office again.

/Henrik

Have you solved this?

erikorrsjo — Wed, 28 Oct 2015 13:27:34 GMT

Have you solved this?

My main problem was that I had not configured correct NAT properly between the interfaces.

Hi, I have a problem, I don't

tadashikanamori — Wed, 25 Nov 2015 23:08:30 GMT

Hi, I have a problem, I don't know if my asa 5506 is wireless, in the chasis have the logo of wifi and have the leyend the "wifi model only", but i don't see the G1/9 and the command: "hw-module module wlan recover configuration" isn't accepted.

I need help, please!

Thanks

Hi tadashikanamori, the white

Henrik Rostgaard Soerensen — Thu, 26 Nov 2015 08:04:10 GMT

Hi tadashikanamori, the white label on the buttom of the chassis, should say ASA5506W if it has the WIFI option.

Best regards

Henrik.

Hi erikorrsjo.

Henrik Rostgaard Soerensen — Thu, 26 Nov 2015 08:05:30 GMT

Hi erikorrsjo.

No unfurtunaly not.

Can you specify the solution you found?

Best regards

Henrik

Hi Henrik,

Rishabh Seth — Thu, 26 Nov 2015 08:30:47 GMT

Hi Henrik,

Try following:

hw-module module wlan recover configuration

asa# session wlan console

ap>enable
Password: Cisco
ap#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

ap(config)#ip default-gateway 192.168.10.1
ap#copy run start

Then try accessing the wlan GUI.

Hope it helps!!!

Thanks,

R.Seth

Thanks R.Seth.

Henrik Rostgaard Soerensen — Thu, 26 Nov 2015 09:16:17 GMT

Thanks R.Seth.

But I have tried that and onces again right now.

I not able to open the GUI in any way I have found in the documentation.

http://192.168.10.1
https://192.168.10.1
http://192.168.10.1:1065

http://192.168.10.2
https://192.168.10.2
http://192.168.10.2:1065

I'm out of ideas now.

/Henrik

Re: Hi Erik.Did you solve this

james.tran77 — Sat, 01 Aug 2020 05:42:33 GMT

The problem is that http server is not enable by default.

From the asa, console to AP

ciscoasa# Session wlan console

Ap> enable secret (you must change the default secret to configure)

Ap# conf t

Ap# ip http server

Ap# ip default-gateway 192.168.10.1

Copy run start