topic Sub-interfaces on PO in Network Security https://community.cisco.com/t5/network-security/sub-interfaces-on-po/m-p/1898124#M436615 <HTML><HEAD></HEAD><BODY><P>Hello Sande,</P><P></P><P>That is correct! Please mark this question as answered so future users having a similar problem can learn from your</P><P>solution.</P><P></P><P>Regards,</P><P></P><P>Julio</P></BODY></HTML> Sat, 19 May 2012 05:03:48 GMT Julio Carvajal 2012-05-19T05:03:48Z Sub-interfaces on PO https://community.cisco.com/t5/network-security/sub-interfaces-on-po/m-p/1898122#M436613 <P>Hi, I have put 2 physicl interfaces (te0/8 &amp; 9) on the ASA-5585 into a PO and am assigning ips/vlans to the sub-interfaces. I have 2 issues: - Why am I not able to ping the other sub-interface from the ASA itself? (I can ping the 1st one), Secondly, why the IPs are not visible in "sh int ip brief" ?Although I can see them in "sh ip" ..</P><P></P><P>/actNoFailover(config-if)# int po17.100</P><P>/actNoFailover(config-subif)# vlan 100</P><P>/actNoFailover(config-subif)# ip add</P><P>/actNoFailover(config-subif)# ip address 100.1.1.1 255.255.255.0</P><P>/actNoFailover(config-subif)# int po17.101</P><P>/actNoFailover(config-subif)# vlan 101</P><P>/actNoFailover(config-subif)# ip address 101.1.1.1 255.255.255.0</P><P>/actNoFailover(config-subif)# int po17.102</P><P>/actNoFailover(config-subif)# vlan 102</P><P>/actNoFailover(config-subif)# ip address 102.1.1.1 255.255.255.0</P><P><STRONG>/actNoFailover(config-subif)# ping 100.1.1.1</STRONG></P><P>Type escape sequence to abort.</P><P>Sending 5, 100-byte ICMP Echos to 100.1.1.1, timeout is 2 seconds:</P><P>!!!!!</P><P>Success rate is 100 percent (5/5), round-trip min/avg/max = 30/32/40 ms</P><P><STRONG>/actNoFailover(config-subif)# ping 101.1.1.1</STRONG></P><P>Type escape sequence to abort.</P><P>Sending 5, 100-byte ICMP Echos to 101.1.1.1, timeout is 2 seconds:</P><P>?????</P><P></P><P><STRONG>/actNoFailover(config)# sh int ip brie</STRONG></P><P>Interface&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; IP-Address&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; OK? Method Status&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Protocol</P><P></P><P>TenGigabitEthernet0/8&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; unassigned&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; YES unset&nbsp; up&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; up</P><P>TenGigabitEthernet0/9&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; unassigned&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; YES unset&nbsp; up&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; up</P><P>Port-channel17&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; unassigned&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; YES unset&nbsp; up&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; up</P><P>Port-channel17.100&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; unassigned&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; YES manual up&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; up</P><P>Port-channel17.101&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; unassigned&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; YES manual up&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; up</P><P>Port-channel17.102&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; unassigned&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; YES manual up&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; up</P><P></P><P>Please advise? </P> Mon, 11 Mar 2019 23:08:45 GMT https://community.cisco.com/t5/network-security/sub-interfaces-on-po/m-p/1898122#M436613 sandevsingh 2019-03-11T23:08:45Z Sub-interfaces on PO https://community.cisco.com/t5/network-security/sub-interfaces-on-po/m-p/1898123#M436614 <HTML><HEAD></HEAD><BODY><P>Ok, i found the answer: - You have to assign "nameif" to the subinterfaces, they are pinging now and also&nbsp; the ips are visible in "sh int ip brief". </P></BODY></HTML> Fri, 18 May 2012 14:58:49 GMT https://community.cisco.com/t5/network-security/sub-interfaces-on-po/m-p/1898123#M436614 sandevsingh 2012-05-18T14:58:49Z Sub-interfaces on PO https://community.cisco.com/t5/network-security/sub-interfaces-on-po/m-p/1898124#M436615 <HTML><HEAD></HEAD><BODY><P>Hello Sande,</P><P></P><P>That is correct! Please mark this question as answered so future users having a similar problem can learn from your</P><P>solution.</P><P></P><P>Regards,</P><P></P><P>Julio</P></BODY></HTML> Sat, 19 May 2012 05:03:48 GMT https://community.cisco.com/t5/network-security/sub-interfaces-on-po/m-p/1898124#M436615 Julio Carvajal 2012-05-19T05:03:48Z