topic Re: Secondary firewall not pulling the configuration (failover) in Network Security

Secondary firewall not pulling the configuration (failover) from primary

kunal-united — Mon, 11 Mar 2019 21:49:49 GMT

Hi,

10.10.194.254 is interface ip on nameif apps and standby configure don this router is 10.10.194.253.

But secondary firewall is not pulling the config from primary firewall and it is taking the ip 10.10.194.250 instead of 10.10.194.253.

can ping both failover interface ip's.

firewallB#

interface GigabitEthernet0/1

description APPS

speed 1000

duplex full

nameif apps

security-level 95

ip address 10.10.194.250 255.255.255.0 standby 10.10.194.251

firewall-A

firewall-A# sh ip | incl FAILOVER

GigabitEthernet0/3 FAILOVER 10.10.30.1 255.255.255.252 unset

firewall-B# sh ip | incl FAILOVER

GigabitEthernet0/3 FAILOVER 10.10.30.1 255.255.255.252 unset

GigabitEthernet0/3 FAILOVER 10.10.30.2 255.255.255.252 unset

firewall-A# PING 10.10.30.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.10.30.2, timeout is 2 seconds:

!!!!!

FIREWALLA# sh failover state

State Last Failure Reason Date/Time

This host - Secondary

Standby Ready Ifc Failure 04:41:41 EST Nov 13 2011

management: Failed

Other host - Primary

Active Comm Failure 20:58:19 EST Oct 28 2011

====Configuration State===

Sync Done - STANDBY

====Communication State===

Mac set

FIREWALLA# show failover interface

interface FAILOVER GigabitEthernet0/3

System IP Address: 10.10.30.1 255.255.255.252

My IP Address : 10.10.30.2

Other IP Address : 10.10.30.1

firewallA# show failover statistic

tx:2461308

rx:5093552

CFWINT1A# show failover statistic

tx:2461313

rx:5093567

firewallA# sh failover

Failover On

Failover unit Secondary

Failover LAN Interface: FAILOVER GigabitEthernet0/3 (up)

Unit Poll frequency 1 seconds, holdtime 15 seconds

Interface Poll frequency 5 seconds, holdtime 25 seconds

Interface Policy 1

Monitored Interfaces 3 of 250 maximum

Version: Ours 8.2(1), Mate 8.2(1)

Last Failover at: 20:58:04 EST Oct 28 2011

This host: Secondary - Standby Ready

Active time: 38 (sec)

slot 0: ASA5540 hw/sw rev (2.0/8.2(1)) status (Up Sys)

Interface dmz (192.168.167.249): Normal (Waiting)

Interface apps (10.10.194.251): Normal (Waiting)

Interface fcn (207.194.137.227): Normal (Not-Monitored)

Interface dcn (204.50.68.253): Normal (Not-Monitored)

Interface management (10.20.197.14): Normal

slot 1: empty

Other host: Primary - Active

Active time: 1348715 (sec)

slot 0: ASA5540 hw/sw rev (2.0/8.2(1)) status (Up Sys)

Interface dmz (192.168.167.248): Normal (Waiting)

Interface apps (10.10.194.250): Normal (Waiting)

Interface fcn (207.194.137.218): Normal (Not-Monitored)

Interface dcn (204.50.68.254): Normal (Not-Monitored)

Interface management (10.20.197.13): Normal

slot 1: empty

Stateful Failover Logical Update Statistics

Link : FAILOVER GigabitEthernet0/3 (up)

Stateful Obj xmit xerr rcv rerr

General 169060 0 5227919 2029415

sys cmd 169060 0 169060 0

up time 0 0 0 0

RPC services 0 0 0 0

TCP conn 0 0 620125 309349

UDP conn 0 0 2018108 1719440

ARP tbl 0 0 2420626 626

Xlate_Timeout 0 0 0 0

VPN IKE upd 0 0 0 0

VPN IPSEC upd 0 0 0 0

VPN CTCP upd 0 0 0 0

VPN SDI upd 0 0 0 0

VPN DHCP upd 0 0 0 0

SIP Session 0 0 0 0

Logical Update Queue Information

Cur Max Total

Recv Q: 0 6 6496542

Xmit Q: 0 1 169060

interface GigabitEthernet0/0

description DMZ - CSWDMZ1A-2/0/10

speed 1000

duplex full

nameif dmz

security-level 50

ip address 192.168.167.254 255.255.255.0 standby 192.168.167.253

interface GigabitEthernet0/1

description APPS -

speed 1000

duplex full

nameif apps

security-level 95

ip address 10.10.194.254 255.255.255.0 standby 10.10.194.253

interface GigabitEthernet0/3

description LAN/STATE Failover Interface

speed 1000

duplex full

interface Management0/0

nameif management

security-level 100

ip address 10.20.197.13 255.255.255.0 standby 10.20.197.14

management-only

Am I missing something?

Please help.

Secondary firewall not pulling the configuration (failover) from

Julio Carvajal — Sun, 13 Nov 2011 19:27:55 GMT

Hello Kunal,

Can you post the running-config of both devices in order to take a deeper look into this issue, also which device has this ip address: 10.10.194.250.

Just to let you know if this interfaces belong to the Stand by device the config is incorrect because both devices got to be configured on the same way and as you wrote on the post the secondary device should get the ip address of

10.10.194.253 when failover occurs so I think that is the problem

interface GigabitEthernet0/0

ip address 192.168.167.253 255.255.255.0 standby 192.168.167.254

Let me know if this makes a difference,

Regards,

Julio

Re: Secondary firewall not pulling the configuration (failover)

kunal-united — Mon, 14 Nov 2011 01:33:40 GMT

Primary- firewall-config

interface GigabitEthernet0/1

description APPS -

speed 1000

duplex full

nameif apps

security-level 95

ip address 10.10.194.254 255.255.255.0 standby 10.10.194.253

failover

failover lan unit primaryfailover lan interface FAILOVER GigabitEthernet0/3

failover link FAILOVER GigabitEthernet0/3

failover interface ip FAILOVER 10.10.30.1 255.255.255.252 standby 10.10.30.2

secondary firewall-config

interface GigabitEthernet0/1

description

speed 1000

duplex full

nameif apps

security-level 95

ip address 10.10.194.250 255.255.255.0 standby 10.10.194.251 <<<<<<<<<<<<<<<<<<<<<

failover

failover lan unit secondary

failover lan interface FAILOVER GigabitEthernet0/3

failover link FAILOVER GigabitEthernet0/3

failover interface ip FAILOVER 10.10.30.1 255.255.255.252 standby 10.10.30.2

Re: Secondary firewall not pulling the configuration (failover)

Julio Carvajal — Mon, 14 Nov 2011 02:18:54 GMT

Hello Kunai,

On the secondary you have configured different the interface gb 0/1 from the Primary, please change that on the one that iincorrect, because on the primary you are let him know that if something happens (failover) use 10.10.194.253 as the standby ip address BUT on the stand-by unit you have configured the ip to 10.10.194.251.

So change that and everything will work.

Please rate helpful comments,

Regards,

Julio

Re: Secondary firewall not pulling the configuration (failover)

kunal-united — Mon, 14 Nov 2011 03:14:19 GMT

But question here is if I configured the primary as below. The secondary should get the configuration automatically right?

Primary router

interface GigabitEthernet0/1

description APPS -

speed 1000

duplex full

nameif apps

security-level 95

ip address 10.10.194.254 255.255.255.0 standby 10.10.194.253

so secondary should get the ip 10.10.194.253 ..why is it getting 10.10.194.250?

Thanks

Re: Secondary firewall not pulling the configuration (failover)

varrao — Mon, 14 Nov 2011 06:42:54 GMT

Hi Kunal,

Whenever you are configuring failover, you just need these 6-7 commands on the secondary:

ASA(config)#failover lan unit secondary
ASA(config)#failover lan interface FAILOVER Gigabitethernet0/3
ASA(config)#failover interface ip FAILOVER 10.10.30.1 255.255.255.252 standby 10.10.30.2
ASA(config)#interface GigabitEthernet0/3
ASA(config-if)#no shut 
ASA(config-if)#exit

ASA(config)# failover

Remember the order of these commands is very important, it shoudl be in the same order as above.
Failover command should be used at the end.

You need not configure any other command on the secondary ASA, only these, the moment you enter
"failover", the two firewalls would starting syncing up.

Do not configure anything else on secondary firewall.

Hope that helps.

Thanks,
Varun