topic Regarding Site to Site VPN in Network Security

Regarding Site to Site VPN

Janardhan Meesala — Mon, 11 Mar 2019 21:02:15 GMT

Dear Experts!!!!!!!!!!

I am using two routers to configure site to site VPN.

one is Cisco 2811 and another one is Cisco 1841 router.

Is we need any license to configure IPSec VPN between these routers.

I am giving sh version output for your reference.

ISCO-2811R#sh version
Cisco IOS Software, 2800 Software (C2800NM-ADVSECURITYK9-M), Version 12.4(22)YB7
, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Mon 27-Sep-10 19:05 by prod_rel_team

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

CISCO-2811R uptime is 16 minutes
System returned to ROM by reload at 06:55:16 UTC Fri Jul 22 2011
System image file is "flash:c2800nm-advsecurityk9-mz.124-22.YB7.bin"

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 2811 (revision 53.50) with 237568K/24576K bytes of memory.
Processor board ID FHK1114F3PQ
6 FastEthernet interfaces
2 Serial(sync/async) interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

CISCO-2811R#

CISCO-1841R#sh ver
CISCO-1841R#sh version
Cisco IOS Software, 1841 Software (C1841-ADVSECURITYK9-M), Version 12.4(18c), RE
LEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 05-Sep-08 12:23 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

CISCO-1841R uptime is 18 minutes
System returned to ROM by reload at 06:49:12 UTC Fri Jul 22 2011
System image file is "flash:c1841-advsecurityk9-mz.124-18c.bin"

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 1841 (revision 7.0) with 115712K/15360K bytes of memory.
Processor board ID FHK114420AA
2 FastEthernet interfaces
2 Serial(sync/async) interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
31360K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

CISCO-1841R#

Please advice me to go further...

Regards,

Janardhan

Regarding Site to Site VPN

Jitendra Siyag — Fri, 22 Jul 2011 15:24:23 GMT

i have checked in the feature navigator and according to that you 2811 image will support the ipsec but your 1841 image will not support ipsec.

check for an image supporting ipsec for 1841 .

Regarding Site to Site VPN

Janardhan Meesala — Fri, 22 Jul 2011 17:07:23 GMT

Dear Jitendra!!!!

Thanks for your response!!!!

But i configured GRE tunneling with IPSec on both same routers and successfully packets was encrypted.

At the same time i configured IPSec VPN on both routers and tunnel came up but there was a some ping issue.

So that i asking is there any related with license or not????

Regards,

Janardhan

Regarding Site to Site VPN

Jitendra Siyag — Sat, 23 Jul 2011 03:21:34 GMT

if your vpn is up and running then it will not e a license issue.

perhaps you should check the configuration. are you facing this issue only for icmp or whole traffic for that tunnel?

Regarding Site to Site VPN

Janardhan Meesala — Sat, 23 Jul 2011 04:56:45 GMT

Currently i am checking only Ping between these two sites....

From Local interface of Site-A is pinging from the System is connected to Local interface of Site-B but not vice-versa...

Please advise me??

Regards,

Janardhan

Regarding Site to Site VPN

Janardhan Meesala — Sat, 23 Jul 2011 05:14:54 GMT

For your reference i am attaching my two sites configuration.

I verified with

Sh crypto ipsec sa

Sh crypto isakmp

For both commands i got out put with packet encapsulated and decapsulated.

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

hostname CISCO-1841R

boot-start-marker

boot-end-marker

enable password nipun

no aaa new-model

ip cef

ip auth-proxy max-nodata-conns 3

ip admission max-nodata-conns 3

crypto isakmp policy 10

authentication pre-share

crypto isakmp key JANNU address 192.168.15.210

crypto ipsec transform-set MYSET esp-3des esp-md5-hmac

crypto map MYMAP 10 ipsec-isakmp

set peer 192.168.15.210

set transform-set MYSET

match address 112

interface FastEthernet0/0

ip address 192.168.15.220 255.255.255.0

ip access-group 113 in

ip access-group 113 out

ip nat outside

ip virtual-reassembly

duplex auto

speed auto

crypto map MYMAP

interface FastEthernet0/1

ip address 20.20.20.1 255.255.255.0

ip access-group 113 in

ip access-group 113 out

ip nat inside

ip virtual-reassembly

duplex auto

speed auto

interface Serial0/0/0

no ip address

shutdown

clock rate 2000000

interface Serial0/0/1

no ip address

shutdown

clock rate 2000000

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 192.168.15.99

ip http server

no ip http secure-server

ip nat inside source list 111 interface FastEthernet0/0 overload

access-list 111 deny ip 20.20.20.0 0.0.0.255 10.10.10.0 0.0.0.255

access-list 111 permit ip 20.20.20.0 0.0.0.255 any

access-list 112 permit ip 20.20.20.0 0.0.0.255 10.10.10.0 0.0.0.255

access-list 113 permit ip 10.10.10.0 0.0.0.255 20.20.20.0 0.0.0.255

access-list 113 permit ip 20.20.20.0 0.0.0.255 10.10.10.0 0.0.0.255

access-list 113 permit udp host 192.168.15.210 host 192.168.15.220 eq non500-isakmp

access-list 113 permit udp host 192.168.15.220 host 192.168.15.210 eq non500-isakmp

access-list 113 permit udp host 192.168.15.210 host 192.168.15.220 eq isakmp

access-list 113 permit udp host 192.168.15.220 host 192.168.15.210 eq isakmp

access-list 113 permit esp host 192.168.15.210 host 192.168.15.220

access-list 113 permit esp host 192.168.15.220 host 192.168.15.210

access-list 113 permit ahp host 192.168.15.210 host 192.168.15.220

access-list 113 permit ahp host 192.168.15.220 host 192.168.15.210

access-list 113 permit tcp any any

access-list 113 permit udp any any

access-list 113 permit icmp any any

access-list 113 permit esp any any

access-list 113 permit ahp any any

access-list 113 permit ip any any

control-plane

line con 0

line aux 0

line vty 0 4

exec-timeout 0 0

password nipun

scheduler allocate 20000 1000

end

Regarding Site to Site VPN

Jitendra Siyag — Sun, 24 Jul 2011 04:08:11 GMT

this is only one site configuration.

is this a test router and if then have you tried to remove the nat and then try. or you can also check the debug messages.