topic ntp in pix in Network Security https://community.cisco.com/t5/network-security/ntp-in-pix/m-p/333958#M550396 <P>Hi All</P><P>Can any one confirm that wether i can enable NTP in pix and have ntp association with ntp master in my network which is also a cisco box configured as ntp master</P><P></P><P>Regards</P><P>Parthiban</P><P></P> Fri, 21 Feb 2020 08:01:17 GMT ponparthi 2020-02-21T08:01:17Z ntp in pix https://community.cisco.com/t5/network-security/ntp-in-pix/m-p/333958#M550396 <P>Hi All</P><P>Can any one confirm that wether i can enable NTP in pix and have ntp association with ntp master in my network which is also a cisco box configured as ntp master</P><P></P><P>Regards</P><P>Parthiban</P><P></P> Fri, 21 Feb 2020 08:01:17 GMT https://community.cisco.com/t5/network-security/ntp-in-pix/m-p/333958#M550396 ponparthi 2020-02-21T08:01:17Z Re: ntp in pix https://community.cisco.com/t5/network-security/ntp-in-pix/m-p/333959#M550398 <HTML><HEAD></HEAD><BODY><P>Hi parthiban</P><P></P><P>yeah.. u can run NTP in cisco firwall OS more than 6.2.. NTP was introduced in 6.2 IOS.. once you have 6.2, u can configure NTP server IP address and md5 secret and get connected to a NTP server.</P><P></P><P>example config:</P><P>ntp authentication-key 1 md5 ********</P><P>ntp trusted-key 1</P><P>ntp server 10.0.6.5 key 1 source inside</P><P></P><P>see if this URL helps you...</P><P></P><P><A class="jive-link-custom" href="http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00801d449c.shtml" target="_blank">http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00801d449c.shtml</A></P><P></P><P>rate replies if found useful..</P><P></P><P>Raj</P><P></P></BODY></HTML> Thu, 17 Mar 2005 10:26:17 GMT https://community.cisco.com/t5/network-security/ntp-in-pix/m-p/333959#M550398 sachinraja 2005-03-17T10:26:17Z Re: ntp in pix https://community.cisco.com/t5/network-security/ntp-in-pix/m-p/333960#M550400 <HTML><HEAD></HEAD><BODY><P>Hi Raj</P><P>Thanks for the response. </P><P></P><P>Could you please tell me where in i have pix in failover and the ntp server is on the inside interface of my firewalls. Here how can i have a ipsec tunnel between my failover boxes. I hope whatever the config i have on my primary active will sync with secondary standby. Should i go to two boxes sep and enable ipsec tunnel for ntp to work with pix.</P><P>Please explanin</P><P></P><P>Regards</P><P>Parthiban</P></BODY></HTML> Fri, 18 Mar 2005 06:48:32 GMT https://community.cisco.com/t5/network-security/ntp-in-pix/m-p/333960#M550400 ponparthi 2005-03-18T06:48:32Z