pix firewall error

alcher — Fri, 21 Feb 2020 07:52:04 GMT

Can somebody help me?

After i upgrade(cisco technical advice) my PIX Version 4. something to PIX Version 6.3(3). I get this error.

Finesse Bios V3.3

Booting Floppy

Loading from Flash

################################################################################

#########################

32MB RAM

mcwa i82558 Ethernet at irq 11 MAC: 0090.270f.24e2

mcwa i82558 Ethernet at irq 10 MAC: 0090.271a.f13e

Flash=AT29C040A @ 0x300

Obsolete FLASH card. Upgrade required. See release notes for this version.

Cisco PIX Firewall Version 6.3(3)

Licensed Features:

Failover: Enabled

VPN-DES: Enabled

VPN-3DES-AES: Enabled

Maximum Physical Interfaces: 6

Maximum Interfaces: 12

Cut-through Proxy: Enabled

Guards: Enabled

URL-filtering: Enabled

Inside Hosts: Unlimited

Throughput: Unlimited

IKE peers: Unlimited

This PIX has an Unrestricted (UR) license.

open(ffsdev/2/read) failed

An internal error occurred. Specifically, a programming assertion was

violated. Copy the error message exactly as it appears, and get the

output of the show version command and the contents of the configuration

file. Then call your technical support representative.

assertion "fdf_init()" failed: file "pix_init.c", line 82

snap_dump_to_flash(): Unable to write crash to flash.

No thread name

Traceback:

0: 004c5f2d

1: 002e82df

2: 002edd7e

3: 001006a0

4: 001000ae

vector 0x00000003 (breakpoint)

edi 0x002e81b0

esi 0x00000052

ebp 0x0009fee8

esp 0x0009fedc

ebx 0x002e81bb

edx 0x000003fd

ecx 0x0000000a

eax 0x0000003a

error code n/a

eip 0x004c983c

cs 0x00000008

eflags 0x00000046

CR2 0x00000000

Stack dump: base:0x0009fe5c size:64, active:64

0x0009ff5c: 0x001016b6

0x0009ff58: 0x00974318

0x0009ff54: 0x00974294

0x0009ff50: 0x007200fc

0x0009ff4c: 0x004c5b6e

0x0009ff48: 0x01feb000

0x0009ff44: 0x01ff4000

0x0009ff40: 0x005148f4

0x0009ff3c: 0x002edd7e

0x0009ff38: 0x0009ffc8

0x0009ff34: 0x00000000

0x0009ff30: 0x00000002

0x0009ff2c: 0x002e82c7

0x0009ff28: 0x002e81b0

0x0009ff24: 0x00000052

0x0009ff20: 0x002e81bb

0x0009ff1c: 0x002e82df

0x0009ff18: 0x0009ff38

0x0009ff14: 0x003c0064

0x0009ff10: 0x6165722f

0x0009ff0c: 0x322f7665

0x0009ff08: 0x01feb000

0x0009ff04: 0x01ff4000

0x0009ff00: 0x02000000

0x0009fefc: 0x00000052

0x0009fef8: 0x002e81bb

0x0009fef4: 0x002e81b0

0x0009fef0: 0x004c5ec0

0x0009feec: 0x004c5f2d

0x0009fee8: 0x0009ff18

0x0009fee4: 0x00000046

0x0009fee0: 0x00000008

0x0009fedc: 0x004c983c *

0x0009fed8: 0x0000003a

0x0009fed4: 0x0000000a

0x0009fed0: 0x000003fd

0x0009fecc: 0x002e81bb

0x0009fec8: 0x0009fedc

0x0009fec4: 0x0009fee8

0x0009fec0: 0x00000052

0x0009febc: 0x002e81b0

0x0009feb8: 0x00000003

0x0009feb4: 0x00104ff9

0x0009feb0: 0x0009fee8

0x0009feac: 0x00000046

0x0009fea8: 0x00000008

0x0009fea4: 0x004c983c

0x0009fea0: 0x0000003a

0x0009fe9c: 0x0000000a

0x0009fe98: 0x000003fd

0x0009fe94: 0x002e81bb

0x0009fe90: 0x0009fedc

0x0009fe8c: 0x0009fee8

0x0009fe88: 0x00000052

0x0009fe84: 0x002e81b0

0x0009fe80: 0x00000003

0x0009fe7c: 0x0009fe80

0x0009fe78: 0x0009feb8

0x0009fe74: 0x0000000a

0x0009fe70: 0x002e81b0

0x0009fe6c: 0x00000052

0x0009fe68: 0x002e81bb

0x0009fe64: 0x2c737261

0x0009fe60: 0x001000ae

Hardware: AL440LX, 32 MB RAM, CPU Pentium II 233 MHz

Flash unknown @ 0x0, 0MB

BIOS Flash unknown @ 0x0, 0KB

0: ethernet0: address is 0000.0000.0000, irq 11

1: ethernet1: address is 0000.0000.0000, irq 10

Nested traceback attempted via interrupt.

Traceback output ab

Re: pix firewall error

gfullage — Thu, 13 Jan 2005 23:44:56 GMT

Your Flash card (Flash=AT29C040A) is a 2Meg flash card. The release notes for 6.3 state that you need at least 8Meg flash to run this image.

You will have to purchase a 16Meg flash card (we don't actually make 8Meg flash cards for the PIX) and swap out the existing 2Meg flash card.

In the meantime to get your PIX up and running, you'll need to downgrade back to your old version until you can swap out the flash.

topic pix firewall error in Network Security

pix firewall error

Re: pix firewall error