topic ASA 5520 in Network Security

ASA 5520

rouzbehta — Mon, 11 Mar 2019 19:40:09 GMT

Hello All,

I have a ASA 5520, when I try to login to webinterface "which has already been configured with a username and password" it gives me this error message " 404 not found the requested URL /admin/index.html was not found on this server.

I am pretty sure that username and password are correct.

Could you please help me out on this issue?

Best Regards,

-Rouzbeh

Re: ASA 5520

Maykol Rojas — Wed, 26 Jan 2011 17:25:05 GMT

Hi,

Would you please add your show version? It seems like the ASA is not picking the image up, Also add the show run asdm command. Try to upload the latest recommended for your version and let us know the results.

http://www.cisco.com/en/US/docs/security/asa/compatibility/asamatrx.html

Cheers

Mike

Re: ASA 5520

rouzbehta — Wed, 26 Jan 2011 18:04:57 GMT

Hello Mike,

I could console to it and get information as follow:

Regards,

-Rouzbeh

Cisco Adaptive Security Appliance Software Version 7.0(6)

Compiled on Tue 22-Aug-06 13:22 by builders

System image file is "disk0:/asa706-k8.bin"

Config file at boot was "startup-config"

ciscoasa up 53 mins 52 secs

Hardware: ASA5520-K8, 2048 MB RAM, CPU Pentium 4 Celeron 2000 MHz

Internal ATA Compact Flash, 256MB

BIOS Flash M50FW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

Boot microcode : CNlite-MC-Boot-Cisco-1.2

SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03

IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04

0: Ext: GigabitEthernet0/0 : address is 001a.e268.402a, irq 9

1: Ext: GigabitEthernet0/1 : address is 001a.e268.402b, irq 137

2: Ext: GigabitEthernet0/2 : address is 001a.e268.402c, irq 9

3: Ext: GigabitEthernet0/3 : address is 001a.e268.402d, irq 9

4: Ext: Management0/0 : address is 001a.e268.4029, irq 11

5: Int: Not licensed : irq 11

6: Int: Not licensed : irq 5

Licensed features for this platform:

Maximum Physical Interfaces : Unlimited

Maximum VLANs : 100

Inside Hosts : Unlimited

Failover : Active/Active

VPN-DES : Enabled

VPN-3DES-AES : Enabled

Security Contexts : 2

GTP/GPRS : Disabled

VPN Peers : 750

This platform has an ASA 5520 VPN Plus license.

Serial Number: JMX1116L13H

Running Activation Key: 0xa628f575 0x587752f0 0xe8127578 0xbbe82088 0x4b1f3787

Configuration register is 0x1

Configuration has not been modified since last system restart.

ciscoasa# sh run asdm

asdm image disk0:/asdm-631.bin

no asdm history enable

Re: ASA 5520

jkinsler — Wed, 26 Jan 2011 20:20:11 GMT

Rouzbeh,

Can you see if you have

http server enable

and

http (IP address) inside

in your config?

thanks

Re: ASA 5520

dguse — Wed, 26 Jan 2011 21:28:42 GMT

Can you run ASDM 6.3(1) with ASA ver 7.0?

Re: ASA 5520

Maykol Rojas — Wed, 26 Jan 2011 21:41:42 GMT

Hi,

Your problem is the following, you are running ASA version 7.0 with ASDM 6.3. On the matrix that I sent you, i states that Version 7.0 the latest that It can run is 5.0.8.

Please refer to the matrix that I sent you

http://www.cisco.com/en/US/docs/security/asa/compatibility/asamatrx.html

Thanks

5510, 5520, 5540

ASA 7.0

ASDM 5.0. Recommended: 5.0(8).

Mike

Re: ASA 5520

rouzbehta — Wed, 26 Jan 2011 22:39:18 GMT

Cool I upgraded the IOS to 8.2(2) And it works.

Thank you very much!

-Rouzbeh