topic PIX 515E and PDM ?!!! in Network Security https://community.cisco.com/t5/network-security/pix-515e-and-pdm/m-p/226225#M592006 <P>I try to configure my PIX515E (version 6.3.2) with a PIX Device Manager (version 3.0.1). I've got already a configuration (from an other PIX-PIX515 version 6.3.2), so I want to configure my new PIX as the old one, but with the PDM.And I've got some problems:</P><P>-PDM ignores some commands:</P><P> fixup protocol dns maximum-length 512</P><P> fixup protocol tftp 69</P><P> access-list NoNat permit ip host 10.147.333.31 host 192.168.10.20</P><P> and all my access-list command !!!</P><P> So where's the problem ?!</P><P>-I've got an other problem, a strange one.</P><P> When I use this command (nat (inside) 1 10.147.333.0 255.255.255.0 0 0) with the telnet configuration, there's no problem, when I refresh the PDM with the running configuration, it's good too, I see it in "Transaltion Rules", but when I wan't to use the same command with the PDM, it's impossible, I've got a problem with the "address pool", I can only choose "same adress". So I don't understand why ...</P><P>I hope you understand me, I'm a newbie with PIX and VPN ...</P><P>Thanks a lot for your help !!</P><P></P><P> and more ....</P> Fri, 21 Feb 2020 07:27:03 GMT adriengourdin 2020-02-21T07:27:03Z PIX 515E and PDM ?!!! https://community.cisco.com/t5/network-security/pix-515e-and-pdm/m-p/226225#M592006 <P>I try to configure my PIX515E (version 6.3.2) with a PIX Device Manager (version 3.0.1). I've got already a configuration (from an other PIX-PIX515 version 6.3.2), so I want to configure my new PIX as the old one, but with the PDM.And I've got some problems:</P><P>-PDM ignores some commands:</P><P> fixup protocol dns maximum-length 512</P><P> fixup protocol tftp 69</P><P> access-list NoNat permit ip host 10.147.333.31 host 192.168.10.20</P><P> and all my access-list command !!!</P><P> So where's the problem ?!</P><P>-I've got an other problem, a strange one.</P><P> When I use this command (nat (inside) 1 10.147.333.0 255.255.255.0 0 0) with the telnet configuration, there's no problem, when I refresh the PDM with the running configuration, it's good too, I see it in "Transaltion Rules", but when I wan't to use the same command with the PDM, it's impossible, I've got a problem with the "address pool", I can only choose "same adress". So I don't understand why ...</P><P>I hope you understand me, I'm a newbie with PIX and VPN ...</P><P>Thanks a lot for your help !!</P><P></P><P> and more ....</P> Fri, 21 Feb 2020 07:27:03 GMT https://community.cisco.com/t5/network-security/pix-515e-and-pdm/m-p/226225#M592006 adriengourdin 2020-02-21T07:27:03Z Re: PIX 515E and PDM ?!!! https://community.cisco.com/t5/network-security/pix-515e-and-pdm/m-p/226226#M592007 <HTML><HEAD></HEAD><BODY><P>Can you post your config? I had some similar problems when going from a 506 to a 515. </P></BODY></HTML> Tue, 08 Jun 2004 13:48:35 GMT https://community.cisco.com/t5/network-security/pix-515e-and-pdm/m-p/226226#M592007 manaughl 2004-06-08T13:48:35Z