topic Re: New to 5510 in Network Security

New to 5510

katiehazlett7 — Mon, 11 Mar 2019 18:15:22 GMT

I would like some help please.

We have purchased a 5510 and I am new to this piece of equipment and need some help.

I have found a lot of information but they seem to mostly use the commend line and I am using the ASDM to configure my information. I just want a connetion from the inside to outside using PAT and then allowing outside traffic in.

I know it shouldn't be that difficult but I don't have a lot of time to devote to configuring this equipment and there is no one else to do it.

I would appreciate any assistance that anyone could provide.

Thanks

Re: New to 5510

Joshua Engels — Fri, 23 Jul 2010 13:48:00 GMT

Hi Katie,

What version of software is currently loaded? 8.2, 8.3 etc? From the CLI, do a "sho ver"

you'll see a line like this...Cisco Adaptive Security Appliance Software Version 8.3(1)

Re: New to 5510

Jitendriya Athavale — Fri, 23 Jul 2010 13:54:21 GMT

http://www.howtocisco.com/cisco/asanat1.htm

entire asdm guide

http://www.cisco.com/en/US/docs/security/asa/asa80/asdm60/user/guide/nat.html

Re: New to 5510

katiehazlett7 — Fri, 23 Jul 2010 14:01:21 GMT

Sorry I should have added that 8.3 is what I am using.

Thank you

Re: New to 5510

Joshua Engels — Fri, 23 Jul 2010 14:03:43 GMT

Note on the guides that jathaval posted: Make sure that your versions line up. 8.0 vs 8.3 etc. Things will be similar between guides but you want to be aware if you are working between guide version and OS/ASDM version. Slight differences etc.

Re: New to 5510

Joshua Engels — Fri, 23 Jul 2010 14:10:54 GMT

Here are the CLI commands. Just substitue your inside network address scheme in place of 192.168.1.0 255.255.255.0.

If you have already setup your outside and inside interfaces this should work: If you have not setup those interfaces, that will need to be done first.

object network my-inside-network
subnet 192.168.1.0 255.255.255.0

nat (inside,outside) dynamic interface

Also, here are the links to the ASA config Guide for 8.3 for ASDM and CLI:

http://www.cisco.com/en/US/docs/security/asa/asa83/asdm63/configuration_guide/config.html

http://www.cisco.com/en/US/docs/security/asa/asa83/configuration/guide/config.html

Re: New to 5510

katiehazlett7 — Fri, 23 Jul 2010 14:21:38 GMT

Thank you so much, I will try that out.

I do appreciate your assistance.

Re: New to 5510

Joshua Engels — Fri, 23 Jul 2010 18:46:00 GMT

Sure. Let us know how it goes

Re: New to 5510

katiehazlett7 — Fri, 20 Aug 2010 20:34:09 GMT

Just to let you know this did not work for me. I am not getting out.

Thanks

Kate

Re: New to 5510

Nagaraja Thanthry — Fri, 20 Aug 2010 20:41:56 GMT

Hello,

Please try the following:

Assume that your inside network is 192.168.1.0/24. Your outside IP is 100.1.1.2 with ISP gw of 100.1.1.1

interface eth 0/0

nameif outside

security-level 0

ip address 100.1.1.2 255.255.255.0

exit

interface eth 0/1

nameif inside

security-level 100

ip address 192.168.1.1 255.255.255.0

exit

route outside 0.0.0.0 0.0.0.0 100.1.1.1

object network LAN

subnet 192.168.1.0 255.255.255.0

nat (inside,outside) source dynamic any interface

Please replace the sample IP addresses with actual IP's of your network.

Hope this helps.

Regards,