topic Re: Management Interaface IPS 4240 in Network Security https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738113#M85868 <HTML><HEAD></HEAD><BODY><P>Hi,</P><P>Thnx for the solution but i already tryed this its not happening, is there anything like need to open the web server port or allowed ip address to access the web innterface. </P></BODY></HTML> Mon, 27 Aug 2007 04:30:54 GMT ram_hiwale 2007-08-27T04:30:54Z Management Interaface IPS 4240 https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738111#M85861 <P>The management interface of IPS 4240 is disabled by default can anyone tell me how to enable this interface.</P><P>I hv just done the basic setup and not able to access the IPS through Web browser</P> Sun, 10 Mar 2019 10:45:56 GMT https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738111#M85861 ram_hiwale 2019-03-10T10:45:56Z Re: Management Interaface IPS 4240 https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738112#M85865 <HTML><HEAD></HEAD><BODY><P>management interfaces are disabled by default and they always are </P><P></P><P>on the cisco ips run </P><P>setup and once you setup an Ip for the ips you will be able to connect to the web interface</P><P></P><P>here is a example of how a command-control should look like </P><P>ex:</P><P> name: FastEthernet0/1</P><P> -----------------------------------------------</P><P> media-type: tx <PROTECTED></PROTECTED></P><P> description: <DEFAULTED></DEFAULTED></P><P> admin-state: disabled <PROTECTED></PROTECTED></P><P> duplex: full default: auto</P><P> speed: auto <DEFAULTED></DEFAULTED></P><P> alt-tcp-reset-interface</P><P> -----------------------------------------------</P><P> none</P><P> -----------------------------------------------</P><P> -----------------------------------------------</P><P> -----------------------------------------------</P><P> subinterface-type</P><P> -----------------------------------------------</P><P> none</P><P> -----------------------------------------------</P><P> -----------------------------------------------</P><P> -----------------------------------------------</P><P> -----------------------------------------------</P><P> -----------------------------------------------</P><P> command-control: FastEthernet0/1 <PROTECTED></PROTECTED></P><P> bypass-mode: auto <DEFAULTED></DEFAULTED></P><P> interface-notifications</P><P> -----------------------------------------------</P><P> missed-percentage-threshold: 0 percent <DEFAULTED></DEFAULTED></P><P> notification-interval: 30 seconds <DEFAULTED></DEFAULTED></P><P> idle-interface-delay: 30 seconds <DEFAULTED></DEFAULTED></P><P></P><P></P><P>as you see they are "protected" so you cannot change the state from disable to enable </P><P></P></BODY></HTML> Sun, 26 Aug 2007 14:40:06 GMT https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738112#M85865 Rodrigo Gurriti 2007-08-26T14:40:06Z Re: Management Interaface IPS 4240 https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738113#M85868 <HTML><HEAD></HEAD><BODY><P>Hi,</P><P>Thnx for the solution but i already tryed this its not happening, is there anything like need to open the web server port or allowed ip address to access the web innterface. </P></BODY></HTML> Mon, 27 Aug 2007 04:30:54 GMT https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738113#M85868 ram_hiwale 2007-08-27T04:30:54Z Re: Management Interaface IPS 4240 https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738114#M85884 <HTML><HEAD></HEAD><BODY><P>You are using HTTPS right, and not just HTTP?</P><P></P><P><A class="jive-link-custom" href="HTTPS://" target="_blank">HTTPS://</A><SENSOR_IP></SENSOR_IP></P></BODY></HTML> Mon, 27 Aug 2007 16:48:45 GMT https://community.cisco.com/t5/network-security/management-interaface-ips-4240/m-p/738114#M85884 mhellman 2007-08-27T16:48:45Z