topic Re: ASA Failover unit (Failed) in Network Security https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044373#M894518 <HTML><HEAD></HEAD><BODY><P>When I try 'failover' command on standby unit, the refresh happens.</P><P></P><P>FWSM/actNoFailover(config)# failover</P><P>FWSM/act(config)#</P><P> Detected an Active mate</P><P>Beginning configuration replication from mate.</P><P>Access Rules Download Complete: Memory Utilization: &lt; 1%</P><P>End configuration replication from mate.</P><P></P><P>But I haven't been able to find any documentation on this. Is 'failover' the right command. </P></BODY></HTML> Sat, 25 Oct 2008 14:34:55 GMT new_networker 2008-10-25T14:34:55Z ASA Failover unit (Failed) https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044372#M894517 <P></P><P>Hi, </P><P></P><P>Is there any entry to refresh/re-enforce the failover configuration in case the secondary unit fails and the interfaces go into 'Normal(Waiting)' state.</P> Mon, 11 Mar 2019 14:02:48 GMT https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044372#M894517 new_networker 2019-03-11T14:02:48Z Re: ASA Failover unit (Failed) https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044373#M894518 <HTML><HEAD></HEAD><BODY><P>When I try 'failover' command on standby unit, the refresh happens.</P><P></P><P>FWSM/actNoFailover(config)# failover</P><P>FWSM/act(config)#</P><P> Detected an Active mate</P><P>Beginning configuration replication from mate.</P><P>Access Rules Download Complete: Memory Utilization: &lt; 1%</P><P>End configuration replication from mate.</P><P></P><P>But I haven't been able to find any documentation on this. Is 'failover' the right command. </P></BODY></HTML> Sat, 25 Oct 2008 14:34:55 GMT https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044373#M894518 new_networker 2008-10-25T14:34:55Z Re: ASA Failover unit (Failed) https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044374#M894521 <HTML><HEAD></HEAD><BODY><P>hi</P><P>try sh failover state</P><P></P><P></P></BODY></HTML> Mon, 27 Oct 2008 14:22:13 GMT https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044374#M894521 SOL10 2008-10-27T14:22:13Z Re: ASA Failover unit (Failed) https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044375#M894524 <HTML><HEAD></HEAD><BODY><P>write standby</P><P></P><P></P></BODY></HTML> Mon, 27 Oct 2008 16:47:27 GMT https://community.cisco.com/t5/network-security/asa-failover-unit-failed/m-p/1044375#M894524 srue 2008-10-27T16:47:27Z